H-Channel for Enclosed Trailers to Build Doors

Question

Question:

I need to build 4 exterior side entry cargo trailer doors. They are made with aluminum “h” channel. Do you have any channel specific to this purpose? Thanks

asked by: Doug

0

Expert Reply:

Yes, we do have some "H" channel that is designed to be used for enclosed trailer cabinets and doors.

- H-Channel for Enclosed Trailer # 36281-955

The # 36281-955 measures 93-1/2" long x 2" tall x 1-1/8" deep and can be cut to fit your needs.

expert reply by: Scott S

0

Answer 1

The trailer hub part #AKIHUB-440-2-1K matches exactly what you would need. Bearings, bolt pattern and stud dimensions are the exact same.

view full answer...

Answer 2

Yes, there should be a washer of some type between the spindle nut and the bearing on your trailer. The washer protects the back side of the bearing from the edges and points on the back side of the spindle nut. There are several types of spindle…

view full answer...

Answer 3

In general for trailer clearance lights you want to have red clearance lights that face the rear of the trailer and then amber that are on the sides or face the sides. I attached a link to a page that has all of the clearance lights we carry as…

view full answer...

Answer 4

The proper mounting location for side marker lights such as #MC32AB are as follows: For rear side marker lights you must have one on each side of your trailer and as far toward the rear of trailer as possible. They will need to be 15 inches or more…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 10

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 11

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 12

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

H-Channel for Enclosed Trailers to Build Doors

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching