Size Nut on B and W Pintle Ball BWTS10051

Question

Question:

What size is the nut on these replacement balls?

asked by: Jake

0

Expert Reply:

The size wrench/socket for the nut of the B and W Pintle Ball # BWTS10051 would be a 1-7/8 inch size.

expert reply by: Jameson C

0

Answer 1

The B&W ball mount #BWBMHD30012 requires a ball with a 1-1/4 inch diameter shank. Ball #BWTS10051 does indeed have a 1-1/4 inch shank so it can be inserted in the ball mount. However it was designed as a replacement for a pintle/ball combo hitch…

view full answer...

Answer 2

The best thing to do when installing trailer lights is to make sure they have the same amount of functions as the ones that you're replacing, and then note what wires are for what functions. This makes it easier to wire up the new tail lights…

view full answer...

Answer 3

Yes you can. If you got the B&W Tow & Stow Pintle Hook with 2-5/16" Ball #BWTS10056 you could use the #BWTS10051 as a replacement 2 inch ball when you needed it.

view full answer...

Answer 4

Hey Brittney. I went out to the warehouse and measured the Replacement Hitch Ball for B&W Tow & Stow Pintle Hook Combo item #BWTS10051. The shank measures 1-7/8" long. What are you needing a 2" hitch ball for? The item #BWTS10051 is…

view full answer...

Answer 5

You can get a 2 inch ball for the B&W Tow & Stow Pintle Hitch, part #BWTS10056 as part #BWTS10051. This is actually a direct replacement for the 2 inch standard version of your hitch, so your shank diameter and lengths will match up very…

view full answer...

Answer 6

The weight capacity of the Curt Pintle Hook with 2-5/16" Ball for 2-1/2" Hitches - 20,000 lbs #C48012 would be decreased when using a 2 inch ball. The Replacement Hitch Ball for B&W Tow & Stow Pintle Hook Combo - 2" #BWTS10051…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Size Nut on B and W Pintle Ball BWTS10051

Continue Researching