Do Screws Hold the Solera Awning Head Cover # LC354185 On

Question

Question:

I purchased a Solera power awning speaker drive head front cover, item #354185. I have viewed some videos online but am unsure as to how to install the cover as I do not see any screw holes as mentioned on the videos. It looks like it just snaps on. Thanks

asked by: Scott C

0

Expert Reply:

There are screws that go through the back cover part # LC300009 that secure it to the front cover part # LC354185. On the inside of the cover you have you can see the holes that the screws attach to.

expert reply by: Jameson C

0

Answer 1

Given the information you were able to provide and from what I can find. The correct replacement for your Solera awning drive head with speaker is the Replacement Solera Awning Speaker Drive Head Front Cover #LC731463 for the front and the Solera…

view full answer...

Answer 2

Hi Rick, We have the following back cover styles for Solera RV Awnings: Edge #LC43UD Plain #LC289561 Plain with speaker #LC300009 Regal #LC643921 I've attached a picture below with the different style heads. If yours looks different then send me…

view full answer...

Answer 3

In order to remove a Solera Awning Head Front Cover like part #LC731463 you will need to remove the screws which hold the front half to the back half. These screws will need to be accessed from the back half of the cover. There are only two screws on…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 8

Hi David! There are quite a few hitches offered for your 2026 Honda Odyssey, so I definitely understand wanting to know the differences. There are basically three styles available for you and I have them broken out below: Exposed Crosstube: etrailer…

view full answer...

Answer 9

Hey Ricardo! Yes, the Curt Trailer Hitch Receiver #C82RJ is the hitch Curt is working on for the new 2027 Telluride. This is a pre-order since Curt hasn't finished the design. It does not include wiring. The wiring harness for the 2027 is also up…

view full answer...

Answer 10

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 11

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 12

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Do Screws Hold the Solera Awning Head Cover # LC354185 On

Products Featured in This Question

Continue Researching