Recommended 16" Long LED Vertical Tail Light

Question

Question:

Looking for a replacement led light. I can send you an image 16” long vertical trailer tail lamp

asked by: Jeremy K

1

Helpful Expert Reply:

We have a couple of options for vertical trailer tail lights that are 16". I have listed them below. These are our only options for 16" long LED tail lights.

16" x 1-5/16" x 11/16" - Optronics ThinLine LED Trailer Tail LIght - Stop, Turn, Tail - Submersible item # STL87RCB

16" x 1-5/16" x 11/16" - Optronics ThinLine LED Trailer Tail LIght - Stop, Turn, Tail - Submersible item # STL87RCPG

expert reply by: Jerred H

1

Answer 1

This particular lamp is meant to be used in pairs, one on each side of the rear of the trailer. The red wire on the drivers side lamp is meant to connect to the yellow wire from the trailer connector, and on the passenger side lamp the red wire…

view full answer...

Answer 2

Hey Jim, The Optronics ThinLine LED Trailer Tail Light #STL87RCB does have Stop, Turn, and Running Light functions so you would be able to use it as a tail light. Typically you'll see these used as tail lights on enclosed trailers because the…

view full answer...

Answer 3

The Optronics ThinLine LED Trailer Tail Light part #STL87RCB is a tail light but if you were instead installing the light to act as a marker light which would be its intended purpose if installed in the center of the trailer then you'd simply…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 11

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Recommended 16" Long LED Vertical Tail Light

Product Page this Question was Asked From

Continue Researching