Do Hubs/Drums Comes with the 7" Dexter Electric Trailer Brake Kit

Question

Question:

Are the hub drums included in this kit? or are they sold separately?

asked by: Samuel A

0

Expert Reply:

The Dexter Electric Trailer Brake Kit part # 23-47-48 does not come with hubs/drums. If you would like to add these as well you'd need the Easy Grease Trailer Hub and Drum Assembly for 2K Axles part # AKHD-545-2-EZ-2K for L44649 (1.063") or part # AKHD-545-2-EZ-1K for L44643 (1") bearings. These are a great cost effective pairing which will work well with these brakes.

expert reply by: Conner L

0

Answer 1

Hello Caden, thanks for reaching out. AL-KO was bought out by Dexter quite a while ago, and many of the old AL-KO brakes use a bolt pattern that is now obsolete. The current standard 4-bolt brake flange is different, and I have included those…

view full answer...

Answer 2

AxleTek is who makes our etrailer brake assemblies like the #AKEBRK-35-SA. We have found that while not considered to be as much of a premium brand like the Dexter assemblies they work just as well and happen to cost a lot less. To put it a different…

view full answer...

Answer 3

The Kenda Karrier S-Trail ST145/R12 Radial Trailer Tires are excellent options. They have a radial ply so they will run cooler while out on the highway and are offered in both a load range d part #AM10130 and load range e part #AM10140. The Kenda…

view full answer...

Answer 4

The Seal POS1501925TB is for oil and it has an inner diameter of 1.5" and an outer diameter of 1.987". We don't have an oil seal in this size but we do have a grease seal, the Grease Seal part #10-9 which measures 1.500" inner…

view full answer...

Answer 5

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 8

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 9

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 10

The Demco Hydraulic Trailer Brake Actuator part #DM72VR should be a direct replacement for the Atwood 61101 Brake Actuator that you have now. This newest updated it rated at 7K instead of 6K. This is a bolt on option that mounts on 3" centers.…

view full answer...

Answer 11

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 12

Hi Calvin! All of the pre-greased hubs/drums, like the Terran Industries Trailer Hub and Drum Assembly - 3.5K Axles - 10" Diameter - 5 on 4-1/2 #TX68VJ, come with bearings made overseas and are all basically the same quality. At least that I…

view full answer...

Do Hubs/Drums Comes with the 7" Dexter Electric Trailer Brake Kit

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching