Replacement Hardware Kit For A Curt Hitch On A 2021 Mercedes-Benz Sprinter 2500
Published 12/07/2022
Products Featured in This Question
Question:
Hello, I recently installed the 13358 Class III hitch. Due to rust on the existing bolts, I opted to use anti-seize on the threads. I forgot to lower the torque on the bolts due to the addition of the anti-seize lubricant and think that I may have overtorqued the bolts as I used the 79 ft-lb. I was wondering if I should replace the bolts on the hitch and re-install them without lubricant, torqued to the specified 79 ft-lb. If so, do you know where I can get replacement hardware? Thank you!
asked by: Warrick
Expert Reply:
If the bolts on your Curt Trailer Hitch Receiver - Custom Fit - Class III # 13358 are a little over torque that is not a big deal and should not pose an issue.
If you don't feel good about it and would rather just replace the hardware, you are going to need M12 x 1.75 Hex bolts, with a .375 x 1.25 x 2.00" round hole spacer, with a M12 x 1.75 flange nut.
Or
You can use our replacement hardware kit # RHK which will contain all the needed hardware for installation. For the "hitch item number" you will just need to type 13358 for your hitch and you'll be good to go.
If you have any other questions feel free to reach out.
Product Page this Question was Asked From
Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- For Towing
- Class III
- 500 lbs TW
- 5000 lbs GTW
- 7500 lbs WD GTW
- 2 Inch Hitch
- 750 lbs WD TW
- Visible Cross Tube
- CURT
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Shop: Ducted Air Distribution Box for Furrion Chill Cube RV Air Conditioners - White - R32
- Q&A: Recommended Handrail For A MORryde StepAbove 4-Step Assembly
- Search Results: kona shocks
- Search Results: furrion chill cube
- Shop: Replacement Hardware Kit for Trailer Hitches
- Shop: LaSalle Bristol RV Waste Valve - Sewer Wye - Rotating - 3" and 1.5" Hubs to 3" Lug
- Shop: MORryde Locking RV Storage Box - 10" Deep x 25-3/4" Wide x 10" Tall - 1-1/2 cu ft
- Shop: Valterra RV Ceiling Vent w/ Dampers and Covered Screws - 5" Diameter - Medium White
- Shop: Handrail for Second Generation 4-Step MORryde Steps
- Shop: Valterra RV Ceiling Vent w/ Filter - Covered Screws - Rotating - 5" Diameter - Lt Beige
- Search Results: awning motor
- Search Results: wacko
- Q&A: Can Dometic Duo Therm RV AC Unit be Replaced with GE Appliances Deluxe AC
- Shop: Gooseneck Hitch
- Shop: Trailer Hitch
- Video: A Closer Look at the 7" Round Transit Turn Signal Light
- Search Results: trailer hitch
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Article: Trailer Wiring Diagrams
- Video: Firestone Ride-Rite Air Bags with Easy Mount Compressor Feature Breakdown
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Shop: Trailer Wiring
- Q&A: Does etrailer Carry Furrion Chill Cube w/ Heat Pump to Replace Dometic Duo-Therm
- Search Results: trailer tires and wheels
- Article: How to Measure for Trailer Hitch Drop
- Shop: Suspension Enhancement
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Search Results: trailer wiring
- Shop: Brake Controller
- Video: How to Choose a Trailer Brake Controller
on Trailer Hitch
