Lift Kit Recommendation for Trailer with Tandem Lippert 3,500 lb Axles

Question

Question:

I need a 2 lift kit for a travel trailer with tandem lippert 3500 axles 1 3/4 leaf springs. The axle is a2 3/8 axle.

asked by: Tony J

0

Expert Reply:

For your trailer that has tandem Lippert 3,500 lb axles we have the Correct Track Tandem Axle lift kit part # RR23QX which lifts the trailer by 2-1/4 inches.

expert reply by: Jameson C

0

Answer 1

It's not uncommon for a trailer with a 29-1/2 inch axle spacing to use either 7-3/4 inch or 5-3/4 inch (or similar) equalizers but the shorter ones are more commonly used with the 25-1/4 inch leaf springs, like the ones you have, designed for up…

view full answer...

Answer 2

The Dexter Over Under kit only works on trailers that have leaf spring suspension. We do have torsion axle lift kits like what you have on your trailer but we would need to know what brand and capacity your axle is. From previous customers most…

view full answer...

Answer 3

The Axle Riser Kit - Single Diamond Torsion Axle - 3-1/2" Lift #LC270682 is the only lift kit we have available for your axle. This is a slightly higher lift than you referenced at 3-1/2 inches, but I think it will work well for you giving you…

view full answer...

Answer 4

Yes. Based off the serial number provided (thank you for the pictures) you've got a Lippert Diamond tube torsion axle, so you will want to use the Axle Riser Kit #LC270682 on your 2017 Jayco Hummingbird 17RK. This kit provides 3-1/2" of…

view full answer...

Answer 5

Since you mentioned you are traveling on gravel and rocky roads, the best option is to go with a 205/75-14 bias tire as opposed to a radial tire. The reason is, the cords inside a bias ply tire run at a 32 degree angle to the direction of travel,…

view full answer...

Answer 6

For your 2014 Jeep Grand Cherokee, a weight distribution system is not required with the light weight of the travel trailer. However, the reason why many would choose to use a weight distribution system on a trailer that is 2,900 lbs is to help…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 12

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Lift Kit Recommendation for Trailer with Tandem Lippert 3,500 lb Axles

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching