Option for Moving Spring Seat of 89 inch Trailer Axle

Question

Question:

Im curious in purchasing the 89 axle with 4 for my boat trailer axle broke do you have a way of moving the spring mounts to the 70 mark? 74 goes beyond the leaf springs

asked by: Henry H

0

Expert Reply:

We cannot move the spring seats here on our 89 inch axles like the # e95SR that you referenced and we only have options that are spaced 74 inches apart like this one. In order for you be able to use this axle you'd have to have new ones welded on like the part # TRSS238.

expert reply by: Jameson C

0

Answer 1

Hey Paul, this is a great question but basically you can rotate the assemblies forward or back so that you can access the adjustment window as needed. Or if the assemblies you have are self adjusting you wouldn't ever really have to mess with it.…

view full answer...

Answer 2

Hi Tobin, The springs seats on the Trailer Axle w/ Electric Brakes #e95SR could be cut off and new spring seats #TRSS238 can be welded onto the axle tube by a certified welder where you need them to sit.

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 6

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 7

You can use leaf springs that are rated higher than the axle without any issues as long as they measure the correct measurement for your trailer. For example the 6-leaf double eye spring for 7,000 lb axles part #e64SR measures 24-7/8" eye to…

view full answer...

Answer 8

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 9

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 12

Hi Calvin! All of the pre-greased hubs/drums, like the Terran Industries Trailer Hub and Drum Assembly - 3.5K Axles - 10" Diameter - 5 on 4-1/2 #TX68VJ, come with bearings made overseas and are all basically the same quality. At least that I…

view full answer...

Option for Moving Spring Seat of 89 inch Trailer Axle

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching