Trailer Hitch that Fits 2022 Kona N

Question

Question:

Your website is incorrect along with Curts. This hitch Curt #11638 was just installed on my 2022 Kona N by my local auto shop. Requires no modification. Please update your website. I tried to call Curt technical support so they would update their website but they were not helpful.

asked by: MARK M

1

Helpful Expert Reply:

Thanks for passing that info on! It's good to know that the Curt hitch 11638 part # C87DR does fit the 2022 Hyundai Kona N.

expert reply by: Jameson C

1

2022 Kona N with Hitch Installed
(click to enlarge)

Answer 1

The Bolt Lock Core part #BL7023480 is compatible with the key of a 2015 Chevy as long as it looks like the key in the picture. How this works is that when you receive the lock core it is "blank". You will put your key in the core and turn…

view full answer...

Answer 2

A 6-Way round pole connector can be wired one of two ways; with the center pole as the 12 volt hot lead, or as the brake. Having the center pole as the 12 volt hot lead is probably most common. In your case, the 6-Way round connector on your Dodge is…

view full answer...

Answer 3

The Replacement FootBase for Thule Tracker #753-2149 is what you currently have on the Thule tracks on your Leer shell. This footbase is for the now discontinued Thule Tracker square bar setup. You may be able to piece this system together even…

view full answer...

Answer 4

Yes, the Rapid Podium Feet for Thule Crossbars - Fixed Point - Qty 4 #TH460R will allow you to attach aero-style Thule crossbars on top of your Leer topper with Thule tracks. The Rapid Podium Feet will fit right into the tracks. If you need a…

view full answer...

Answer 5

Thanks for reaching out, Hal! That's a really good question. Based off what I could find, if the old cylinder worked with your ignition key you would want to get part #BL692918. I included the ignition key compatibility diagram below for you. You…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 10

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Trailer Hitch that Fits 2022 Kona N

Continue Researching