Trailer Hitch Confirmed to Fit a 2022 Tesla Model Y to Carry a Bike Rack

Question

Question:

Is there a hitch that will fit my 2022 Tesla Model Y that has a 2" receiver? Been trying to find one to carry my bike rack that has a 2" shank.

asked by: Bart

0

Expert Reply:

Yes, there is a hitch that will fit your 2022 Tesla Model Y.

- EcoHitch Invisi Trailer Hitch Receiver # EH39FR

The EcoHitch Invisi Trailer Hitch Receiver # EH39FR is made in the USA, has a bolt-on, no-drill installation and will provide you with the 2" hitch receiver that you are needing for your bike rack. The 2" receiver is the most common size used for hitch mounted accessories such as bike racks, cargo carriers and ball mounts.

expert reply by: Scott S

0

Answer 1

I did some online research. Your 2022 Tesla Model Y's tow package comes rated to tow up to 3,500 lbs and with a 7-way connector already installed. You will still need some more items to tow the Flaggstaff Epro 15TB. You will need a brake…

view full answer...

Answer 2

I do have a solution for you, however there is definitely not enough ground clearance at the hitch connection between your Mazda CX-5 and 6x12 utility trailer. Any slight incline or bump in the road is going to cause issues with your current setup.…

view full answer...

Answer 3

You are really close to getting the correct rise drop but on the trailer side you measure from the ground to the bottom of the coupler lip instead. So you'd most likely have about 21 inches on that side compared to the 18 inches on the vehicle…

view full answer...

Answer 4

Yes, I was able to obtain the following photos of the #EH39FR EcoHitch for the 2020 Tesla Model Y.

view full answer...

Answer 5

The Curt Class III hitch, part #C13416 is the easiest to install hitch we offer for your RAV4. The majority of the hitch will be concealed behind the bumper, which many folks seem to prefer. If you'll be towing with the hitch, you'll need a…

view full answer...

Answer 6

Without knowing how much clearance you need from your hitch pin hole center to the rear of the bumper fascia I cannot know for sure which size will fit your 2021 Tesla Model Y. I do know on the Draw-Tite Receiver #DT58MR we found a 4" distance…

view full answer...

Answer 7

Hey Jonathan, you are correct. The etrailer Adjustable Ball Mount #E66PR has been tested on a 2024 Nissan Frontier and because the hitch receiver sits too far inside (only 3" from hitch pin hole to bumper), this ball mount will hit the bumper…

view full answer...

Answer 8

Draw-Tite has been around a lot longer than Curt, but both make a high quality product, you can't go wrong either way. If your CX-5 has a Diesel motor, you'll use the Draw-Tite Class III hitch, part #DR44FR which is the only fit offered. If…

view full answer...

Answer 9

Yes, the Curt Towing Starter Kit #C45534 will come with the hitch ball mounted for the 2" drop but you can definitely remove it, flip the ball mount to the 3/4" rise position, and then reinstall the hitch ball. If your 2021 Tesla Model Y…

view full answer...

Answer 10

To tow the rental trailer you mentioned level you'll need a ball mount that has a 4 inch rise with the Draw Tite hitch part #75758 that you referenced. So for that we have the Curt #C45070 which would work well. Then for a hitch ball you'll…

view full answer...

Answer 11

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Trailer Hitch Confirmed to Fit a 2022 Tesla Model Y to Carry a Bike Rack

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching