Trailer Wiring Harness Replacement for 2006 Jeep Grand Cherokee to Replace Hopkins Kit

Question

Question:

Hello I bought this from you a few years ago and installed on a 2006 jeep grand Cherokee. It worked great until last year when the left turn and brake light stopped working. I have checked all the wiring and lights, they work fine and will operate when the jeep is not towed and I can plug other lights into the jeep tow connection and they work. If I have diodes bad in this control will I have to replace the entire unit? wiring front to back was time consuming Thanks

asked by: Steven

0

Expert Reply:

If your Hopkins trailer wiring harness part # HM56206 failed the only solution would be an all new harness as just the converter or internal parts are not available for it. The most reliable trailer wiring harness solution we offer for your 2006 Jeep Grand Cherokee would be the Tekonsha kit part # 118394 and would be what I would recommend.

expert reply by: Jameson C

0

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 4

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 5

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 6

Both the Roadmaster and Blue Ox tow bars are great options. But if it was my decision to make I would go with the Blue Ox Avail part #BX7420 as we have found that the Blue Ox tow bars are a little easier to connect and disconnect from. Also this tow…

view full answer...

Answer 7

Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 10

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 11

Hey Tom, great question! Both products provide an easy way to measure tongue weight, but they excel in different situations. The BTBRV Trailer Jack Foot Scale #BTBRV014 measures tongue weight at the trailer jack, so you don't need to position a…

view full answer...

Answer 12

Hey Lucian! There are definitely a lot of options out there, and the best is usually a mix of parts from different manufacturers. We don't have a package under a single part number but I can give you a list of parts for a complete setup. I…

view full answer...

Trailer Wiring Harness Replacement for 2006 Jeep Grand Cherokee to Replace Hopkins Kit

Continue Researching