Can Lippert Polarity Reversing Solenoid LC118246 Be Installed With a Strap

Question

Question:

My present solenoid is trapped to the top of the pump motor with a type of hose clamp. The Part # appears to be 118246. Is the replacement part compatible with the use of this strap.

asked by: Paul

0

Expert Reply:

If the Lippert Polarity Reversing Solenoid # LC118246 looks to be the same design as the 118246 that you're currently using then you should be able to use the strap in the same manner. The only time something would change is if this part looks different than what you have.

expert reply by: Jon G

0

Answer 1

There is a solenoid like in your photo, and it is possible that Replacement Solenoid #LC118246 will fix your issue. I'm guessing that when opening and closing, doing so one way is causing more problems than the other. If so, what you can do is…

view full answer...

Answer 2

Yes, I've attached a wiring diagram for the BaseCamp Hydraulic Leveling System, which depicts how the Lippert Polarity Reversing Solenoid #LC118246 is wired into the system. I'll also send a link to the installation instructions for this…

view full answer...

Answer 3

The Lippert Replacement Reverse Polarity Solenoid for RV Hydraulic Slide-Outs part #LC136046 and part #LC118246 are the same solenoid but vary in how they mount. The part #LC136046 mounts using a strap around the motor like what you have therefore…

view full answer...

Answer 4

The location for the solenoid controller like the Lippert Polarity Reversing Solenoid by Trombetta for Hydraulic Power Units #LC118246 will vary and in order to find what you're looking for you're going to need to trace the wiring going to…

view full answer...

Answer 5

The slide out could be malfunctioning for a number of reasons, but the motor or solenoid can very well be the culprit. Below I've attached a snippet from the manual that goes over how to test both the solenoid #LC118246 and the motor so that you…

view full answer...

Answer 6

I fully understand wanting a backup unit! Based on your information, I recommend the Lippert Components Polarity Reversing Solenoid by Trombetta for Hydraulic Power, Item #LC118246. This polarity reversing solenoid is a cost effective and simple…

view full answer...

Answer 7

You have already successfully tested the solenoid like the Polarity Reversing Solenoid by Trombetta for Hydraulic Power Units #LC118246. Switching the wires is the exact way you want to test this, and since you have done so, you are right that it is…

view full answer...

Answer 8

Most likely you have a bad solenoid on your Trombetta Lippert slide out and would just need to replace it with the part #LC118246. It's very common that this style of slide out has solenoid issues and this is the known solution.

view full answer...

Answer 9

The 214-1231-A61-06 solenoid actually replaced your older 214-1231-A11-06, so the correct replacement for your 06 Keystone Montana Mountaineer is the Lippert Polarity Reversing Solenoid by Trombetta for Hydraulic Power Units #LC118246.

view full answer...

Answer 10

The replacement slide-out solenoid motor you need depends on what model of solenoid you currently have installed on your 2016 Cedar Creed 5th wheel trailer. The only replacement solenoid we carry (and the most often we see) is the Lippert Polarity…

view full answer...

Answer 11

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 12

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Can Lippert Polarity Reversing Solenoid LC118246 Be Installed With a Strap

Product Page this Question was Asked From

Continue Researching