Trailer Coupler Hitch Lock For Dexter DX7.5L A-60 Brake Actuator # DX56FR

Question

Question:

is there a lock available to secure this trailer on my hitch for security?

asked by: David P

0

Expert Reply:

Yes, the etrailer Surge Brake Coupler Lock # e98888 will allow you to lock the Dexter DX7.5L A-60 Brake Actuator # DX56FR to your 2" hitch ball.

We also have the Blue Ox Hitch Receiver and Coupler Latch Lock Set # BLU36XR if you want a matching lock for your hitch in the receiver.

expert reply by: Bud M

0

Answer 1

Hey John, since you have a UFP A-60 surge coupler we have just the inner member with the part #DX39FR or if you want the entire replacement coupler/actuator you'd instead want the part #DX63FR. Both of these are designed for 2 inch hitch balls as…

view full answer...

Answer 2

For as trashed as those brake assemblies are I am impressed with how spotless that spindle is! Based on the bearing numbers you mentioned you have a #84 spindle and the hub part #AKHD-545-35-G-K is correct. Since this its galvanized it's a really…

view full answer...

Answer 3

If the solenoid is getting a full 12 volts and is grounding properly it should be shutting all the way. Since you said it is clicking that makes it sound like it's getting power. You could try improving the ground circuit but most likely…

view full answer...

Answer 4

You actually need the reverse light circuit active on your trailer wiring so that your surge brakes can be temporarily deactived when backing up. So what you'd need is a 4-way to 7-way adapter #37185 and you'd need to connect the purple wire…

view full answer...

Answer 5

Hello Gregg, I think I can help shed some light on what is going on. Basically, there are two ways to stop surge brakes from actuating when backing up the trailer. The first and most popular way to do this is to use a surge brake actuator with a…

view full answer...

Answer 6

Reverse lock out solenoids are not polarity sensitive so you could run either the white or the blue wire of the Dexter coupler part #DX99FR as the power or ground and you'd be totally fine.

view full answer...

Answer 7

Since you have a 7-way, there is one brake controller that you just have to plug in and no other wiring is needed, the Curt Echo Wireless Brake Controller #C51180.

view full answer...

Answer 8

The Trailer Coupler Lock #e98887 will work with a UFP A-60 coupler like your Dexter A-60 #DX56FR. The product picture for this lock shows it being used on an A-60.

view full answer...

Answer 9

The best option I have to activate the reverse lockout feature on a boat trailer would be to first integrate the circuit into the trailer connector with the Hopkins Endurance 5-Way Flat Trailer Connector part #HM47910. Once this is done you can use…

view full answer...

Answer 10

The only difference between the Replacement Inner Member for Dexter DX7.5L Actuator part #DX99FR and part #DX39FR is that the former is for tandem axle trailers with disc brakes and the latter is for single axle trailers with disc brakes or tandem…

view full answer...

Answer 11

Hey Reid, You can do exactly what you were wanting to replace the inner member of your A-60, and since you have a single-axle trailer you do indeed have the right part: - Replacement Inner Member for Dexter DX7.5L Actuator - Single Axle w/ Disc -…

view full answer...

Answer 12

The coupler lock I recommend for your UFP A-60 Coupler is the Coupler Lock, part #e98888. Since the coupler measures 3-inches wide and the pin hole is 1/4 inch diameter the #28012 will work great to secure the coupler. The lock has a covered key slot…

view full answer...

Trailer Coupler Hitch Lock For Dexter DX7.5L A-60 Brake Actuator # DX56FR

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching