Replacement Actuator For An eMoMo 3MTR135-334A

Question

Question:

Where can I find this part fir my recliner it is eMoMo model #3MTR135-334A max load 1000NPush speed mm/sec REV: 3200/min Duty cycle 10 MANU.Date 2018.7

asked by: Kevin R

0

Expert Reply:

The Replacement Actuator for Thomas Payne Seismic Power Recliner # SC96MR is the correct replacement actuator for your eMoMo model 3MTR135-334A.

This actuator fits all Thomas Payne Seismic power recliners.

I attached a review video link below.

expert reply by: Noah E

0

Actuator Replacement
(click to enlarge)

Answer 1

Thanks for the picture of your Thomas Payne actuator setup. Based on seeing that we know the part #SC96MR is the correct replacement.

view full answer...

Answer 2

We have had this asked in the past and I am able to confirm that the Replacement Actuator for Thomas Payne Seismic Power Recliner #SC96MR cross-references with the QDPT-01-002 actuator as the correct replacement. This actuator fits all models of the…

view full answer...

Answer 3

From the issues you are describing, it sounds like you are most likely having an issue with your control box. From what I could find using the pictures you provided, I believe you most likely have the Thomas Payne Seismic Recliner or Sofa which would…

view full answer...

Answer 4

In regards to the actuator for Thomas Payne RV Recliners, there were several different ones used so you may see a few different part numbers floating around. That said, they mostly all use the same current replacement which is the Replacement…

view full answer...

Answer 5

Yes, the Replacement Actuator for Thomas Payne Seismic Power Recliner #SC96MR is a compatible replacement for your QDPT-01-002 actuator. We have also confirmed this with the manufacturer in the past that this is a compatible replacement.

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 10

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 11

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 12

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Replacement Actuator For An eMoMo 3MTR135-334A

Featured Help Information

Miscellaneous Media

Continue Researching