Leg Height of Rhino-Rack Aero Bar Roof Rack for Camper Shells # Y02-480B

Question

Question:

What is the clearance from the underside of the crossbar to the mounting service?

asked by: Ed L

0

Expert Reply:

The distance from the bottom of the crossbar of the Rhino-Rack Aero Bar Roof Rack for Camper Shells # Y02-480B to the track it mounts in measures 3 inches.

expert reply by: Jameson C

0

Answer 1

Hey Jimbo! The Rhino-Rack Aero Bar Roof Rack for Camper Shells item #Y02-480B comes with the tracks, towers, lock covers, feet, mounting hardware, and crossbars. This kit includes everything you'll need to install the roof rack on a camper shell.…

view full answer...

Answer 2

The best option I have for you to carry your kayaks on the camper shell is with the Rhino-Rack Roof Rack System part #Y02-480B which uses tracks so you can slide the crossbars back and forth at will. In regards to installation, you will have to drill…

view full answer...

Answer 3

Yes. You can cut the tracks on the Rhino-Rack Aero Bar Roof Rack for Camper Shells #Y02-480B to 50" long for installation. Although, this may require you to drill new holes in the tracks for the hardware. It is important to note that these…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 10

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Leg Height of Rhino-Rack Aero Bar Roof Rack for Camper Shells # Y02-480B

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching