Installation Instructions And Product Information For The ThermaHeat RV Holding Tank
Updated 08/25/2022 | Published 08/24/2022 >
Question:
is this holding tank heater pad still effective without using the adhesive? id like to avoid making this a permanent installation as my current camping setup is only temporary. does the thermostat / temperature sensor still work if its not stuck directly onto the tank? is there a minimum thickness the water tank needs to be in order for it to work properly and not melt the tank? how hot does the pad get when its on? my plastic water tank is inside a wooden box which has some foam pipe insulation around it to prevent the tank from bouncing directly into the wood. is it okay for the pad to contact wood or foam? id probably install it on the side of the tank as theres a little wiggle room there vs underneath where the bottom sits flat on a piece of 1/2inch plywood. will the heating pad work effectively on the side or top of the tank?
asked by: Mark
Expert Reply:
I spoke with Therma Heat, and they informed me that the ThermaHeat RV Holding Tank or Step Heater Pad w/ Thermostat # 277-000164 must be installed on the bottom of the tank and it must be stuck using the adhesive backing.
These pads are meant to be installed at the lowest point of the tank, closest to the drain, so installing them anywhere else would not be effective.
Additionally, while they did not inform me what the maximum thickness these pads can be installed to, they did let me know that these pads will work with up to a 40 gallon tank, will heat up to 75° in 10 minutes, and requires 13.5VDC for maximum efficiency.
Finally, they did mention that installing this pad where it would rest on wood may cause damage to the unit overtime and it is not recommended to do so.
To get around this, you can cut an access hole in the plywood for this pad (18-1/2" L x 12" W), that way your pad won't be pressed against the plywood, and your holding tank will still be supported by the wood.
Featured Help Information
Miscellaneous Media
Continue Researching
- Shop: Kat's Heaters Ceramic Interior Heater with Fan - 300 Watt - 12V
- Shop: Vehicle Engine Heaters
- Q&A: Can The Kat's Ceramic Interior Heater Be Used In A UTV And Will It Drain The Battery
- Shop: NOCO GEN On-Board Battery Charger - AC to DC - Waterproof - 3 Bank - 12V - 15 Amp
- Q&A: Furrion RV Fridge to Replace Norcold N2118
- Shop: Trailer Hitch
- Shop: Power Mountain Tallboy Off-Road Bottle Jack - 8-1/2" to 37-3/4" Lift - 6 Tons
- Q&A: Lug Nut Torque Chart for Trailer Wheels
- Article: Trailer Wiring Diagrams
- Search Results: trailer hitch
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Shop: Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires
- Shop: Trailer Wiring
- Video: Clean Up Your Trailer Wiring
- Q&A: Recommended Bike Rack and Dual Hitch Adapter for Carrying E-Bikes While Flat Towing
- Search Results: trailer wiring
- Shop: Suspension Enhancement
- Shop: Curt Powered Tail Light Converter with 4-Pole Flat Trailer Connector
- Search Results: trailer tires and wheels
- Article: How to Measure for Trailer Hitch Drop
- Q&A: How to Replace a Lance 6-Pin Plug w/ a Standard 7-Way Connector
- Shop: etrailer Anti-Rattle Hitch Collar for 2" Hitch Receivers
- Search Results: trailer lights
- Q&A: Instructions to Wire a Trailer for Electric Brakes
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Shop: Brake Controller
- Search Results: trailer jack
- Article: How to Measure Your Trailer Wheel Bolt Pattern
- Shop: Gooseneck Hitch
- Q&A: Recommended Flat Tow Setup for a 2026 Ford Maverick
