Replacement Inner And Outer Bearing With Seal For A 1998 Kwik Kamp Camper Trailer

Question

Question:

Have a 1998 Kwik Kamp camper trailer. Usually towed by a motorcycle. Dexter axle 1 1/16. One bearing shows: L44649, no numbers on other bearing. Seal shows: TCM DEXTER 010-009-00 TAIWAN. Looking for 2 sets, inner, outer and seal.

asked by: Richard J

0

Expert Reply:

The Inner bearing and the Outer bearing will be the same at # L44649 they have a 1.063 inch inner diameter. The Inner and Outer Race will be the same # L44610. The correct seal # 10-9 is the seal you will need the 10-9 seal is in cross reference to the TCM Dexter 010-009-00. So you can purchase Bearing Kit # BK1-150 to get all the pieces together.

I attached a review video link below.

expert reply by: Noah E

0

Troy

5/15/2025

i do not recognize this type cotter pin holding the bearing nut on and don't know how to get it off. not standard cotter pin.

Nick S.

5/19/2025

@Troy Hey Troy, are you referring to the cotter pin in kit # BK1-150 or one that is on your trailer now? The one in the kit would just be a normal cotter pin that goes through the spindle, when you need to remove it, you just pull it out. It may take some force.

Answer 1

The best way to confirm the correct replacement wheel bearings and seals for your 1999 Magic Tilt boat trailer is to pull one of the hubs and note the inner and outer bearing numbers and seal number. You can then directly search on those part numbers…

view full answer...

Answer 2

The bearing part #L44649 has an inner diameter of 1.063 and is typically used in 3,500 lb axle hubs and the #L44643 has an inner diameter of 1 inch and is typically used on 2,000 lb axle hubs. If you can get me more info on your trailer like axle…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 6

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 9

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 10

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 11

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 12

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Replacement Inner And Outer Bearing With Seal For A 1998 Kwik Kamp Camper Trailer

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching