Parts Needed For Trailer Connector & Brake Controller On 2022 Chevrolet Express Van Factory Wiring

Question

Question:

I have a new 2022 Chevy express van. It has the factory installed trailering wire harness provision. What do I need to complete the trailer wiring with brake controller? Thank you!

asked by: Mike

1

Helpful Expert Reply:

First you will need to locate the brake controller wires in your 2022 Chevrolet Express van. One you have located the wires you will need to use a Test Light # PTW2993 to verify that the wiring is functioning properly. You should have a power wire, brake switch signal wire, ground wire and a wire going to the 7-way at the back of the vehicle. With all these functioning properly you will be able to connect a Tekonsha Prodigy P3 Trailer Brake Controller # 90195. If they are not functioning you will need to contact your Chevrolet dealer to determine what all is required to get all the wires functioning properly.

For the trailer connector I recommend using the 7- and 4-Pole Trailer Connector Socket w/ Mounting Bracket # HM40975. This will give you a factory style connector with both a 4-way flat and 7-way blade connector. It will connect to the factory connector for the trailer wiring provision on your van.

expert reply by: Bud M

1

Answer 1

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 2

Thanks for the picture Don! I do not have anything that connects to that 10-pin so I am hoping you're just at the wrong connector. I have linked a picture below along with an installation video that will show you what the Hopkins item #31345…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…

view full answer...

Answer 8

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 9

No, it will not Bryan. The Redarc Tow-Pro Link item #RED57AR requires a USCAR port that comes with factory tow packages. The Stealth Hitches Hidden Trailer Hitch Receiver w/ Towing Kit item #SH25VR, that fits your 2023 BMW X5, does not have this…

view full answer...

Answer 10

To install a Redarc Tow Pro Liberty in your 2023 Toyota Tacoma Sport you will need the following parts: Redarc Tow-Pro Liberty Brake Controller item #RED24FR Plug-and-Play Wiring Harness for Redarc Tow-Pro Trailer Brake Controllers item #RED99FR…

view full answer...

Answer 11

Actually, the P3 now has the upgraded axis accelerometer like the P2. The Tekonsha P3 Trailer Brake Controller #90195, will work with both electric over hydraulic brakes on the trailer as well as electric brakes. It has a menu option on the display…

view full answer...

Answer 12

The Redarc Tow-Pro Liberty #RED24FR is the way to go over the Elite #RED44FR as you get the nicer functions of the Elite at a lower price. The Elite has the ability to be the more preferred proportional style of controller as well as a time-delayed…

view full answer...

Parts Needed For Trailer Connector & Brake Controller On 2022 Chevrolet Express Van Factory Wiring

Products Featured in This Question

Continue Researching