Replacement Handle for Reese Tow Power Trailer Jack 74410

Question

Question:

The handle for my Reese Towpower Bolt-on Swivel Trailer Jack part #74410 fell off and was lost. Can I get a replacement handle please?

asked by: Bob W

0

Expert Reply:

You have two choices for a replacement handle for the now obsolete Reese trailer jack 74410. The first option is the Fulton Sidewind 800 lb Handle # F0933301S00. Your second option is the Fulton Sidewind 1500 lb Handle # F0933305S00. The dimensions between these two are very similar.

Our contact at Reese told us that the nut and bolt option handle is no longer available either and this handle is easier to install.

With either handle you simply pull the pin out of the jack (if it is still there) and slide this handle in, replace the pin and tighten down the nut.

expert reply by: Jameson C

0

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 4

Hey Katja, the Curt Echo Mobile brake controller part #C51180 would be your best option. This is a wireless brake controller and all it requires is a 7-way with the taillight functions and the 12 volt accessory circuit active and you'd be set. So…

view full answer...

Answer 5

The Replacement Sidewind Handle #TJD-7000S-HD you're looking at does have a 1/2" diameter so it could work well for you if it matches what you're needing. I'm attaching a few dimensions photos for your reference as well!

view full answer...

Answer 6

Tire designations ST205/75D14 and ST205/75R14 are both for special trailer tires with a 205mm width, 75-percent aspect ratio and that fit a 14-inch wheel. The difference between them is the tire's type of construction. The ST205/75D14 tire is a…

view full answer...

Answer 7

I went and measured the threaded section of the Replacement Sidewind Handle Knob for etrailer and Ram Swivel Marine Jacks #MJ-1000B-KB and found it was approximately 1/2".

view full answer...

Answer 8

I measured the Replacement Sidewind Handles #MJ-1000B-HD and #MJ-1500B-HD and found that they both have a diameter of 1/2" and part MJ-1000B-HD measures 2" from the end of the handle to the center of the pin hole while part MJ-1500B-HD…

view full answer...

Answer 9

Hey Steve, The Specialty Recreation Insta Holding Tank Patch Kit #SR48RR works on all forms of plastic and since polyethylene is a form of plastic you'd be good to go.

view full answer...

Answer 10

The grease seal on your trailer should ideally sit snug on the spindle. You don't want it so tight that you cannot get it on, but there shouldn't really be a gap between it and the spindle, which can allow grease to escape (which you saw in…

view full answer...

Answer 11

We have two Bulldog jacks that use the square pipe mount attachment. We have the Topwind Swivel Jack, #BD195312, and the Sidewind Swivel Jack, #BD195362. Both of these jacks have a 15 inch lift, a 3,000 lb lift capacity and a 5,000 lb static weight…

view full answer...

Replacement Handle for Reese Tow Power Trailer Jack 74410

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching