What is Overall Length of Single Axle Trailer Fender w/ Backing Plate - Ribbed Steel # HP29FR

Question

Question:

With fender sitting on a table, what is measurement from front to back @ table level ? TKS.

asked by: Ken W

0

Expert Reply:

The overall length of the Single Axle Trailer Fender w/ Backing Plate - Ribbed Steel # HP29FR that you referenced is 32 inches from front to back.

expert reply by: Jameson C

0

Answer 1

Thanks for the photo. Honestly 5 inches of clearance from the fender to the top of the tire is fine if that is what you desire. We normally recommend 4 inches to allow for the suspension travel whether with leaf springs or torsion axles to allow…

view full answer...

Answer 2

To install the Single Axle Trailer Fender w/ Backing Plate #HP29FR you need to use the Mounting Brackets #CE26098G-2. The backing plate isn't strong enough but these mounting brackets install to the fender itself so the weight isn't an…

view full answer...

Answer 3

Something like part #HP36VR is probably what you are looking for. It is designed to fit 14-15 inch diameter tires and has a back that is spot welded to the fender.

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 9

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 12

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

What is Overall Length of Single Axle Trailer Fender w/ Backing Plate - Ribbed Steel # HP29FR

Product Page this Question was Asked From

Continue Researching