Replacement Disc Brake Kit For Tie Down Engineering 46845 Disc Brake Hub
Updated 07/14/2022 | Published 07/13/2022
Products Featured in This Question
Question:
I have an older TDE axle with straight shaft spindles...hub # is 46845HECA. both bearings Im told are 1 3/8inch ID. do you have a hub and rotor combo that is compatable? Thanks
asked by: Tyson D
Expert Reply:
I can recommend the Kodiak Disc Brake Kit # K2HR35DKG to give you a new disc brake setup. Your Tie Down Hub 46845 is only a 9.6" diameter rotor and the 10" is the current size available. Your hub uses a Inner Bearing # L68149, Outer Bearing # L44649 and Grease Seal # 168255TB.
The Kodiak Disc Brake Kit # K2HR35DKG will require 2 of the Inner Bearings # L68149, Outer Bearings # L44649 and Grease Seals # 168255TB to mount on your TDE axle. You will also need the Standard Grease Caps # RG04-020, EZ Lube Grease Caps # RG04-040 or the Bearing Buddy Bearing Protectors # BB1980A-SS
Product Page this Question was Asked From
Kodiak Disc Brake Kit - 10" Hub/Rotor - 5 on 4-1/2 - Dacromet and KodaGuard - 3,500 lbs
- Accessories and Parts
- Trailer Brakes
- Disc Brakes
- LH
- RH
- 3500 lbs
- Brake Assembly
- 5 on 4-1/2
- Hub and Rotor Assembly
- Kodiak
more information >
Continue Researching
- Shop: Kenda 4.80/4.00-8 Bias Trailer Tire with 8" White Wheel - 4 on 4 - Load Range B
- Search Results: 480/400~8 trailer tires and wheels
- Shop: Kenda 4.80/4.00-8 Bias Trailer Tire with 8" Galvanized Wheel - 5 on 4-1/2 - Load Range C
- Search Results: fenders
- Search Results: 5 on 4~1/2 inch trailer hubs and drums
- Search Results: l44649
- Search Results: l44649 trailer hubs and drums
- Shop: Trailer Idler Hub Assembly for 2K Axles - 10" to 12" Wheels - 5 on 4-1/2 - Pre-Greased
- Shop: Trailer Idler Hub Assembly for 2K Axles - 10" to 12" Wheels - 5 on 4-1/2 - Pre-Greased
- Shop: Complete Bearing Kit with L44649 Inner/Outer Bearings and 10-9 Grease Seal Fits 1.063" Spindles
- Shop: Dexter Trailer Idler Hub for 2,000-lb and 2,200-lb Axles - 5 on 4-1/2 - Galvanized
- Shop: Easy Grease Trailer Idler Hub Assembly for 2K Axles - 10" to 12" - 5 on 4.5 - Pre-Greased
- Search Results: trailer tongue
- Search Results: front receiver hitch
- Shop: Trailer Hitch
- Shop: Trailer Wiring
- Q&A: Will Aluminum Hi-Spec Series 04 Star Mag Trailer Wheel # AM20258 Work with ST175/80R13
- Q&A: What Brake Kit is the Best Replacement for My Tie-Down Engineering Caliper 46304 on Vortex Hubs?
- Q&A: What is the Difference Between the Kodiak Disk Brake Kits K2R35DKG and K2R35DS?
- Q&A: Recommended Disc Brake System for Salt Water Boat Trailer with Tandem Axles
- Article: Most Popular Wheel Bearings
- Q&A: Replacement Bearing And Seals For UFP Hub H-1062-2
- Q&A: Replacement Inner Member for UFP A-60 Surge Coupler for Tandem Disc Brake Setup
- Q&A: Replacement for UFP A60 Actuator on EZ Loader Boat Trailer
- Article: Trailer Drum Brakes vs. Disc Brakes: Making the Decision
- Article: How to Accurately Measure Trailer Leaf Springs
- Article: Breakaway Kit Installation for Single and Dual Brake Axle Trailers
- Article: Overview of Lubricating Grease
- Article: 5 Tell-Tale Signs It’s Time to Replace Your Trailer’s Leaf Springs
- Article: Happy Holidays from etrailer!