Will Curt Combo Bar With 2" Trailer Hitch Receiver Fit Inside 2-1/2" Receiver
Updated 07/06/2022 | Published 07/04/2022
Products Featured in This Question
Question:
Do you know if this bar will fit into a 2.5” class iv receiver opening? I see above it says wall thickness is 0.21” so I am guessing it measures about 2.42” OD, correct? In which case it should slide into a 2.5” receiver opening?
asked by: JC
Expert Reply:
I went out to our warehouse and measured the Curt Combo Bar with 2" Trailer Hitch Receiver - 48" Long - Unpainted # C49480. It is exactly 2-1/2" x 2-1/2" so it will not fit in your receiver. I'm not 100% sure what you were going to use this for, but if you are looking for a 2-1/2" receiver extension I recommend checking out the Curt Hitch Extension and Reducer for 2-1/2" Trailer Hitches - 24" to 34" Long # C45048.
Product Page this Question was Asked From
Curt Combo Bar with 2" Trailer Hitch Receiver - 48" Long - Unpainted
- Hitch Fabrication Parts
- Receiver Tube
- 48 Inch Long
- Raw Finish
- Fits 2 Inch Hitch
- 1/2 Inch Thick
- CURT
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Video: The Low-Down on the Alpha Systems 1021 Self-Leveling Sealant for RVs
- Search Results: sealer
- Search Results: reese hitch extension
- Search Results: reese 45018
- Search Results: reese hitch extender
- Search Results: reese
- Article: Trailer Wiring Diagrams
- Shop: etrailer Electric Trailer Brakes - Self-Adjusting - 12" - Left/Right Hand - 5.2K to 7K
- Q&A: Lug Nut Torque Chart for Trailer Wheels
- Search Results: trailer tires and wheels
- Article: How to Measure Your Trailer Wheel Bolt Pattern
- Video: etrailer VS Dexter Self Adjusting Brakes Comparison
- Q&A: Instructions to Wire a Trailer for Electric Brakes
- Search Results: trailer jack
- Shop: Easy Grease Trailer Hub and Drum Assembly for 3.5K Axles - 10" - 5 on 4-1/2 - Pre-Greased
- Shop: Trailer Wiring
- Video: Review of etrailer Trailer Hubs and Drums - Hub with Drum - AKHD-545-35-EZ-K
- Q&A: Comparing the eTrailer and Dexter Electric Trailer Brake Kits
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Shop: Trailer Wheel Bearing Kit for Lippert, Dexter, and AL-KO Axles - 3,500 lb with #84 Spindle
- Article: Trailer Drum Brakes vs. Disc Brakes: Making the Decision
- Video: Complete Breakdown of the Dexter Nev-R-Adjust Electric Trailer Brake Assembly
- Q&A: What is a #84 Spindle and How Do I Know I Have One On My Trailer?
- Shop: Dexter Electric Trailer Brakes - 12" - Left/Right Hand Assemblies - 7,000 lbs
- Video: Hands-On with the Hub Saver Hub and Wheel Protector
- Q&A: How to Measure to Determine the Size Trailer Brakes Needed For Hydraulic Drum Replacement
- Shop: etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector
- Article: Trailer Lighting Requirements
- Video: Complete Breakdown of the Timbren Axle-Less Trailer Suspension w/ Idler Hubs
- Q&A: Who Makes The Best Quality Trailer Bearings?
on Hitch Fabrication Parts
