Recommended Trailer Hitch Receiver and Coupler Locks For a 2017 Ram 2500

Question

Question:

I am looking for recommendations for a good quality hitch pin lock for a 2.5inch receiver. my old one from 2inch receiver does not fit and need to find a high quality new one. looking on amazon a lot of the locking pins have bad reviews as far as them seizing up and not being able to remove them. any advice would be appreciated.

asked by: Kyle R

0

Expert Reply:

I recommend looking at the BOLT Trailer Hitch Receiver Lock # BL7018448. This will allow you to use the key for your 2017 Ram 2500 to operate the lock. The shaft is stainless steel to prevent corrosion from allowing you to remove your hitch over long periods of time.

We aslo have their Couper Latch Lock # BL7025286 and Coupler Lock # BL7032492 that can also be keyed to your truck key. This ensures you always know what key you need for all your locks.

expert reply by: Bud M

0

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 4

Hello Joe, Thanks for writing in! Based on the measurements you provided, the Gen-Y Glyder Shock Absorbing Ball Mount #325-GH-12001 is not the right fit for your setup. Since your Tundra's receiver measures 18 inches from the ground and your TAB…

view full answer...

Answer 5

Hey Paul, thanks for the pic! That's a nice setup. It is highly recommended to use a weight distribution system if your trailer weighs 50% more than your truck's total weight and you are definitely there. For a 4,000 lbs cargo trailer, I…

view full answer...

Answer 6

Hey Eddie, the Curt hitch part #C22RJ and the Trailermate part #TMT29FR are both very similar in design and capacity. I really like the Curt hitches and recommend them whenever available but Trailer Mate isn't bad either. If you are wanting the…

view full answer...

Answer 7

Hey Ryan! Yes, the Dexter E-Z Flex Suspension Kit #K71-653-00 is what you need for your Grand Design Imagine. The length of this equalizer matches the Dexter 13-122 that came with your trailer, which is the most important factor so you keep the…

view full answer...

Answer 8

Hey Mike, The #IR29FR lock kit is not compatible to work with the B&W Pintle Hitch that you have. The pin diameters are different sizes and would not fit. The only kit we have that is confirmed to fit the B&W Pintle Hitch is the InfiniteRule…

view full answer...

Answer 9

Hey Rex! Those are some great questions. A weight distribution hitch (WDH) isn't always needed but in your case you will want one. Typically if the weight of your trailer is more than 50% of the weight of your vehicle it is a good idea to use a…

view full answer...

Answer 10

For your 2018 Forest River 197BH, I recommend the Furrion RV Observation Camera System w/ Monitor and Bracket #FOS43TASF. This camera is prewired in your trailer to function when you shift into reverse. It can be rewired to work anytime the running…

view full answer...

Recommended Trailer Hitch Receiver and Coupler Locks For a 2017 Ram 2500

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching