Compatible Weight Distribution Hitch Shank For A Reese WDS That Has More Drop

Question

Question:

I have the reese 49913 setup. With changing trucks the shank that came with setup will not allow me enough to level out camper. I need about 2 more inches. What other shanks are available for this setup?

asked by: Adam L

0

Expert Reply:

We have plenty of options for your Reese Pro Round Bar Weight Distribution w Sway Control # RE44FR!

I recommend taking a look at the:

-Equal-i-zer Weight Distribution Shank # EQ44FR.

This shank has 12" of drop and 15" of rise, which is 3.5" more drop than the shank that came on your Reese WDS system, and is rated for a maximum of 1,400lbs of tongue weight and 14,000lbs of GTW.

expert reply by: Bryce D

0

Answer 1

The weight distribution system you use needs to be rated for the tongue weight of your 2017 Dutchmen Kodiak Ultra-Lite 283BHSL. The #RE94FR has a tongue weight range of 400-800 lbs and your dry tongue weight is 754 lbs so you will easily exceed the…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 5

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 8

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 9

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 10

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 11

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 12

The Demco Hydraulic Trailer Brake Actuator part #DM72VR should be a direct replacement for the Atwood 61101 Brake Actuator that you have now. This newest updated it rated at 7K instead of 6K. This is a bolt on option that mounts on 3" centers.…

view full answer...

Compatible Weight Distribution Hitch Shank For A Reese WDS That Has More Drop

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching