Screen For Keeping Out Insects Compatible with V771232-C Heng's Roof Vent

Question

Question:

I need a screen for my 2005 Alpenlite powered bathroom roof vent. The part number I was able to find with a picture of the screen I need is V771232-C.

asked by: Ronald B

0

Expert Reply:

I recommend installing a MaxxAir Standard RV and Trailer Roof Vent Cover # MA00-933066 on the roof of your RV as it has a bug screen built in that will keep out bugs. We currently do not have a screen that is confirmed to fit the V771232-C Heng's roof vent.

expert reply by: Bud M

0

Answer 1

We do carry a similar kit in the Correct Track Trailer Alignment and Lift Kit #RR23QX as the Lippert kit LC407131 is no longer available from Lippert. The Correct Track kit offers either a 1-1/4" or 2-1/4" lift and allows you to adjust the…

view full answer...

Answer 2

You have a couple of good options. You can use our etrailer.com Coupler Lock, part #e98888, through the latching mechanism on the top of your coupler. This has a wide width so it will clear the sides.

view full answer...

Answer 3

Hey Doug, for your Ventadome V3094 the vent cover you would want would be the MaxxAir part #MA00-933069 which is a universal style vent cover. We don't have anything that is custom fit for the Ventadome at this time.

view full answer...

Answer 4

Hey John. The inside of the Greystone Trim Kit item #FR22EF measures 19" wide by 10-3/8". It's designed for Furrion 0.9 Cu Ft stainless steel microwaves. It has exterior dimensions of 23-3/8" long x 2-13/16" wide x 15"…

view full answer...

Answer 5

For a vent cover to use with the Ventline E-Z Lift Ventadome #V3092-601-00 so that you can attach to the four mounting brackets of the vent you would want to use one specifically designed for it. For that you would want the MaxxAir Cover part…

view full answer...

Answer 6

Hey Rich, the standard Maxxair roof vent cover part #MA00-933066 is what Maxxair recommends to fit your Ventadome. This cover was designed to match up with the 4 mounting points on the Ventadome.

view full answer...

Answer 7

Hey Emily, the Blu Technology RV Pressure Regulator #GB97FR uses the standard 1/4 inch quick disconnect size that is the same as what you would see on an air compressor. Do you have a compressor you could compare to the larger size you have?

view full answer...

Answer 8

For the Ventline E-Z Lift Ventadome Trailer Roof Vent #V3092-601-00, I recommend the MaxxAir Standard RV and Trailer Roof Vent Cover - 19" x 18-1/2" x 9-1/2" - White #MA00-933066. This cover will allow for full vent function and also…

view full answer...

Answer 9

Hey Ron, yes painting the MORryde Short Safe-T-Rail Telescoping RV Hand Rail #MR54RV white would make it a lot less hot in the sun. I would recommend a pretty thin layer on the inner telescoping part since it slides in and out of the outer tube but…

view full answer...

Answer 10

Hello Bruce, Thanks for writing in! Using butyl tape between the trailer body and the Single Axle Jeep Style Trailer Fender - Diamond Plate Aluminum - 13" to 15" #HP96VR is exactly the route I would go. It stays flexible, creates an…

view full answer...

Answer 11

Hey Kyle! That is correct. The Coleman-Mach Mach-C Everest has variable-speed cooling and an inverter-driven compressor. However, the Mach-C Everest uses a traditional wall thermostat instead of a remote control. It also works with both ducted and…

view full answer...

Answer 12

Hey David, you can replace your Coleman Mach 15 with the Coleman Mach Everest part #CM35MR and use the same wiring that's behind the walls. Everything else would need to be swapped out but the wiring can be reused. We only have the Everest in the…

view full answer...

Screen For Keeping Out Insects Compatible with V771232-C Heng's Roof Vent

Product Page this Question was Asked From

Continue Researching