Locking Pin for Brake Actuator Coupler

Question

Question:

How can I lock this coupler so it can not be stolen? The pin hole is very small on the latch and it must be a long pin. Any suggestions? I tried the master lock pin type, Too short. Also tried the big yellow ball thing and that did not fit.

asked by: Bob Z

0

Expert Reply:

You have a couple of good options. You can use our etrailer.com Coupler Lock, part # e98888, through the latching mechanism on the top of your coupler. This has a wide width so it will clear the sides.

expert reply by: DeAnne T

0

Answer 1

We do carry a similar kit in the Correct Track Trailer Alignment and Lift Kit #RR23QX as the Lippert kit LC407131 is no longer available from Lippert. The Correct Track kit offers either a 1-1/4" or 2-1/4" lift and allows you to adjust the…

view full answer...

Answer 2

I recommend installing a MaxxAir Standard RV and Trailer Roof Vent Cover #MA00-933066 on the roof of your RV as it has a bug screen built in that will keep out bugs. We currently do not have a screen that is confirmed to fit the V771232-C Heng's…

view full answer...

Answer 3

We do have a replacement option for you. I was able to locate the measurements of your lock using the numbers you provided. - 5" wide x 4-1/2" tall x 1-1/2" thick The Global Link RV Baggage Door Slam Latch #295-000015 has the same…

view full answer...

Answer 4

The best replacement option we offer for a Atwood GC10A-4E Water Heater is tankless, the Furrion RV Tankless Water Heater part #FR68SR. It won't be a direct replacement but still pretty easy nonetheless as they are very similar. That said, you…

view full answer...

Answer 5

It is possible to move a trailer by just attaching to it's safety cables. Most people would avoid the method you described as the trailer will slam into the back of the tow vehicle while stopping. Basically it wouldn't be a thief's ideal…

view full answer...

Answer 6

I have another option for you but the MaxxTow Coupler Latch Lock for Surge Brake Actuators - 2-1/2" Span - 1/4" Diameter #MT46FR you were looking at cannot be ordered keyed alike. Instead I recommend the etrailer Surge Brake Coupler Lock -…

view full answer...

Answer 7

The Tie Down Engineering (TDE) Brake Actuator 48980 also known as the 80LP/85LP is a 8,000 lb or 8,500 lb disc brake actuator with 2" coupler. In order to replace this, the best option we have is the Demco Hydraulic Brake Actuator part…

view full answer...

Answer 8

We don't offer an 8500 lb rated surge coupler, but we might have options that would work for you. If the GVWR (weight of trailer plug boat) is 8000 lbs or less, I'd recommend the Demco item #DM8669113 if your trailer has disc brakes or item…

view full answer...

Answer 9

A 5/8" pin is the most common diameter used for a swing away tongue. There are different length pins for different height frames. The only one we currently carry is for a 5" tall frame, for this you will use a Pin #F500336. Be sure to…

view full answer...

Answer 10

I do have an option for you but in order to switch an actuator from disc to drum brakes you'd need a new master cylinder. Unfortunately, we don't have any replacement parts for the Tie Down Engineering LP8500 as it's discontinued.…

view full answer...

Answer 11

Hey Anthony! I really like the Trimax Dual Purpose Coupler Lock and U-Lock for 1-7/8", 2", and 2-5/16" Couplers #TMX67FR because it can fit a variety of coupler styles and sies, plus it has the matte-looking finish on it which makes it…

view full answer...

Answer 12

The Dexter DX7.5L A-60 Brake Actuator part #DX89FR for disc or part #DX33FR for drum will work to replace both a UFP A-60 or A-75 Brake Actuator so there will be no worried here. The A-60 is rated for 6K and the A-75 is rated for 7.5K. The Dexter…

view full answer...

Locking Pin for Brake Actuator Coupler

Product Page this Question was Asked From

Continue Researching