Configuration of the Replacement Controlled Motion Hinge

Question

Question:

I ordered the 6 leaf black hinge #258548. They sent me a hinge with the screen leaf in the middle. I need a hinge with the screen leaf on the bottom. Have contacted people with etrailer and Lippert.... They tell me that the 6 leaf that I need has been discontued. What can you tell me????

asked by: Don W

0

Expert Reply:

Correct, the configuration of the Replacement Controlled Motion Hinge, # LC95VR has changed. What you are asking for has been discontinued and replaced with the configuration of what you have received.

expert reply by: Michael R

0

Answer 1

Hey Pedro! Ultimately, you'll be looking to make sure the 4500 Series Converter #PD4575CSV has an output of 13.2 and 14.4 Volts DC (14.6V for a Lithium setup), but there are a number of steps to get to this point which you can find here -…

view full answer...

Answer 2

Hey Cliff, with the Replacement Controlled Motion Hinge #LC95VR to get the desired effect where the door doesn't swing open or closed all you have to do is replace is a single hinge and not all three.

view full answer...

Answer 3

We carry replacement entry door hinges for your 1999 Fleetwood Discovery like with the #LC95VR for black which is a controlled motion hinge and part #LC22NJ for white. Controlled motion hinges hold the door in any position you leave it in so that it…

view full answer...

Answer 4

For a bearing kit that fits the 3,500 lb axle of your Forest River R-Pod 178 the correct part number is the part #BK2-100. This comes with bearings, races and a seal. I also attached an install video for this for you to check out as well.

view full answer...

Answer 5

Hello, and thanks for providing all of that information for your axle. I had my contact at Lippert run the item number and serial number. Your axle is a standard 3,500 lb axle and it used the standard bearing and seal sizing. Our bearing kit #BK2-100…

view full answer...

Answer 6

I would be happy to help you find the correct bearing kit for your 2017 Forest River R-pod 176 Travel Trailer, but unfortunately we do not have a break down of the specific components your trailer uses. Instead what you will need to do is remove one…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 11

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 12

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Configuration of the Replacement Controlled Motion Hinge

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching