Where Are The Americana Metal, Bolt-In Valve Stems Made

Question

Question:

Where is it made

asked by: Kc

0

Expert Reply:

The Americana Metal, Bolt-In Valve Stem - 1-1/4 inch Long # AM20906 is made in China.

I attached a review video link below.

expert reply by: Noah E

0

Answer 1

Hey Tracy, thanks for all of the information. Since your 2025 Silverado 1500 LTZ does not have the Adaptative Ride Control feature, I recommend the Air Lift LoadLifter 5000 Ultimate Air Helper Springs with Internal Jounce Bumpers item #AL88288. The…

view full answer...

Answer 2

Yes, the Americana Metal, Bolt-In Valve Stem #AM20906 will fit your Lionshead Jaguar wheels. These are rated for up to 200 psi.

view full answer...

Answer 3

Unless otherwise stated on the wheel itself, wheels themselves will be able to withstand the psi rating of any tire that is confirmed to fit it. The piece that you will want to look at is the valve stem. If you have a rubber valve stem then the…

view full answer...

Answer 4

Trailer tires and wheels do not typically come balanced from the factory like what you see with standard passenger vehicle tires. This isn't usually needed for trailer tires and most car shops don't have the needed setup to properly balance…

view full answer...

Answer 5

Hey Jason, for a set of metal valve stems that fit your 2023 Grand Design 2910BH we have the part #AM20906 that you referenced which will fit and work great with your TPMS cap sensors.

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

Hey Doug! The Firestone Ride-Rite Air Helper Springs #F35FV are the right kit for your 2026 Ford F-350 FX4 dually. However, you will need to measure to be sure it fits. The distance from the top of your rear axle to the top of the jounce bump stop…

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 10

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 11

Congrats on the new motorhome Edward! SnapPad doesn't have the 2026 Allego Red 38 KA in their system so I don't know what size your jack feet are. However, we have a few options that will work with the HWH leveling systems. What you'll…

view full answer...

Answer 12

Hello Graham, thanks for reaching out. So far I have been pretty impressed with the PacBrake air bags. I would say they are in line with the quality of the Air Lift air bags. They use similar top plates. Pretty much everything about the design of…

view full answer...

Where Are The Americana Metal, Bolt-In Valve Stems Made

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching