How Does Edge Programmer Tune Second Vehicle

Question

Question:

How to hook up to a new vehicle with my edge I got a new one for my other truck so I want to program my other one to another truck

asked by: Johnathon

0

Expert Reply:

You have to first set the old vehicle back to stock so that you can install the programmer like # EP43DR on the new truck. These can only be installed on one vehicle at a time as they lock to a vehicle's VIN.

expert reply by: Jameson C

0

Answer 1

The Mushroom Vent #37202-29125 you found is an entire assembly. We do not offer only the replacement top for this at this time but you can remove just the top portion and use it. If you plan on staying in Flordia you may consider switching to the…

view full answer...

Answer 2

Hi Adam, we have a some different options but it all depends on your configuration. If you have the 8' bed the easiest to use and remove would be the Demco Recon 5th Wheel Trailer Hitch #DM8550045. This 5th wheel hitch only weighs 100 lbs, 50 lbs…

view full answer...

Answer 3

I recommend the Air Lift LoadLifter 7500 XL Air Helper Springs - Rear Axle item #AL57589. The air bag style air helper springs by Air Lift are the only ones that will fit the under bed mount hitch like the B&W Turnoverball Underbed Gooseneck…

view full answer...

Answer 4

Thank you for the photos! From what I'm seeing it looks like you need the Replacement Lift Arm #FVK8011-05 and the Replacement Dome #FVK1020-19 for your main vent. The dome should be an exact replacement while the lift arm doesn't have the…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 12

You can use the RV Propane Gas Detector #RS64FR (white) or #RS44FR (black) to replace your current Atwood 31013 propane gas detector. This will also use a 12v, 2-wire installation like your current detector.

view full answer...

How Does Edge Programmer Tune Second Vehicle

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching