Reverse Lockout Pin For A Dexter TDE 85LP Brake Actuator

Question

Question:

I want to order the reverse lockout pin for a model TDE lp85. Does this pin work?

asked by: Mike S

0

Expert Reply:

The Replacement Damper Pin for Titan Model 10 Brake Actuator # T1593400 that you mentioned is actually meant to work with the Titan Model 10 surge-type brake actuators, however I spoke with Dexter, and they informed me that for your TDE 85LP brake actuator you can use the:

-Replacement Hitch Pin Kit for Dexter Axle Brake Actuators # DX89XR.

expert reply by: Bryce D

0

Answer 1

We have the Replacement Shock #T1242600 for your Titan Model 10 surge brake actuator. The Replacement Master Pin #T1593500 are the ones that hold the rear of the shock with the Replacement Rear Roller #DX46FR. All these are sold as individual items…

view full answer...

Answer 2

To replace the shock in your Titan model 10 actuator you are going to basically need to disassemble the actuator so that you have access to the shocks. Instead of describing to you how it comes apart I thought it would be more helpful if you had an…

view full answer...

Answer 3

Yes, there is a difference between an oil seal and a grease seal for trailer hubs. Oil seals have a much tighter fit on the spindle to keep the oil from leaking out. An oil seal can be used with grease but a grease seal cannot be used with oil. The…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 9

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 10

Hello Sam; that is a great question! I reached out to Furrion and you will be able to use the Furrion Chill Cube #FR69TD (white) or #FR49TD (black) with your furnace. However, the remote is not capable of operating the furnace at this time. Also, we…

view full answer...

Answer 11

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Reverse Lockout Pin For A Dexter TDE 85LP Brake Actuator

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching