Correct Lockout Kit for Demco Hydraulic Brake Actuator DA86

Question

Question:

Can I use item#DM5863 with iem#DM72VR? Please explain why or why not

asked by: Raymond L

0

Expert Reply:

Yes, the Reverse Lockout Solenoid Kit for Demco DA66B Hydraulic Brake Actuators part # DM5836 will work great with the Demco Hydraulic Brake Actuator part # DM72VR.

expert reply by: Conner L

0

Answer 1

Yes, the Reverse Lockout Solenoid Kit for Demco DA66B Hydraulic Brake Actuators item #DM5836 will work great with the Demco Hydraulic Brake Actuator item #DM72VR.

view full answer...

Answer 2

The correct reverse lockout solenoid for the Demco DA86 actuator part #DM72VR is the part #DM5836.

view full answer...

Answer 3

Hey Dustin, The Demco Actuator #DM48CV is in fact for disc brakes and we have to get our page updated! Thank you for pointing that out so we can get that fixed haha. Since you're looking for a drum brake application the actuator you are going to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

The Demco Hydraulic Trailer Brake Actuator part #DM72VR should be a direct replacement for the Atwood 61101 Brake Actuator that you have now. This newest updated it rated at 7K instead of 6K. This is a bolt on option that mounts on 3" centers.…

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 8

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 9

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 10

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 11

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 12

Hey Robert, yes the Kodiak disc brake calipers part #KDBC225DAC that you referenced will replace the Tie Down calipers you have now 46304, they can be used as a left or right hand caliper and does come with ceramic brake pads. If you ever needed…

view full answer...

Correct Lockout Kit for Demco Hydraulic Brake Actuator DA86

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching