Reverse Lockout Solenoid for Demco DA86 Actuator

Question

Question:

which brake lockout can I use with DM72VR?

asked by: Jim P

1

Helpful Expert Reply:

The correct reverse lockout solenoid for the Demco DA86 actuator part # DM72VR is the part # DM5836.

expert reply by: Jameson C

1

Answer 1

Atwood is no longer in business, which means replacement parts are unfortunately no longer available for your Atwood 61101 surge brake actuator. The best option available if yours is no longer working is to replace the actuator, which you can do with…

view full answer...

Answer 2

Demco does not offer a manual lockout for the coupler part #DM72VR but they do offer an electric option with the part #DM5836. They also recommend installing free-backing brake assemblies on the axles instead too which I attached a link to a page…

view full answer...

Answer 3

The Atwood coupler you have has been discontinued for quite some time now which means there are no replacement parts available for it. Now would be the time to replace the coupler with something like the Titan part #DM72VR which we have found works…

view full answer...

Answer 4

The Demco Hydraulic Trailer Brake Actuator part #DM72VR should be a direct replacement for the Atwood 61101 Brake Actuator that you have now. This newest updated it rated at 7K instead of 6K. This is a bolt on option that mounts on 3" centers.…

view full answer...

Answer 5

For a replacement for your Atwood 61101 I recommend the Demco Hydraulic Brake Actuator #DM62VR. This actuator is designed to work with disc brakes and fits a 3" wide trailer tongue with bolt holes 3" apart on center. It comes with an…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

Hey Robert, yes the Kodiak disc brake calipers part #KDBC225DAC that you referenced will replace the Tie Down calipers you have now 46304, they can be used as a left or right hand caliper and does come with ceramic brake pads. If you ever needed…

view full answer...

Answer 11

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 12

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Reverse Lockout Solenoid for Demco DA86 Actuator

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching