Replacement Center Cap for Taskmaster Aluminum Viking Series Vor Trailer Wheel 3.19" Pilot Hole

Question

Question:

Can I buy a replacement cap for this wheel ?

asked by: Curtis G

1

Helpful Expert Reply:

We have the Replacement Center Cap for Taskmaster Viking Aluminum Trailer Wheels # CXF106C that fits the Aluminum Viking Series Vor Trailer Wheel # AX02455545FPS. The only difference in these is the red print that comes on the caps for the wheel versus the silver print on the replacement.

expert reply by: Bud M

1

Answer 1

Hey Jared, thanks for the picture! I would definitely replace the bearings and not just add grease. Replacing the entire hub with bearings takes care of everything so you don't have to worry about it. Since you have 5,200 lb axles you can use the…

view full answer...

Answer 2

Hi Craig; thank you for providing those part numbers. That is the 2.25" inner diameter grease seal so for replacement bearings you can use the Bearing Kit, LM67048/25580 Bearings, 10-36 Seal #BK3-300 you were looking at. If you prefer Timken…

view full answer...

Answer 3

While we don't have that exact part number we do have the similar Wheel Center Cap part #425EZ which fits the pilot hole of a wheel that measures 4.25 inches in diameter and has a removable center section like the part number you mentioned.

view full answer...

Answer 4

The P-29 number you're seeing on your Dexter Axle is actually the number for the plant that made the axle. There should be a stamp or sticker on your trailer frame near the coupler that shows what the axle capacity is, and if you can't find…

view full answer...

Answer 5

The etrailer.com Electric Trailer Brake Kit #AKEBRK-7-SA and the Dexter Nev-R-Adjust Electric Brake Kit # 23-464-465 referenced in your question are both self-adjusting assemblies that will work to replace the existing Dexter brakes on your 7,000…

view full answer...

Answer 6

I sure do Brian and thanks for the information! To add a spare tire mount to your Magic Tilt tandem axle boat trailer, I recommend the Tie Down Spare Tire Mount item #TD86FR. It attaches to frames and tongues up to 8" tall. The Tie Down item…

view full answer...

Answer 7

Hey Tony, standard length stainless lug nuts like the part #DE55KR would be what you'd want to use with the trailer wheel Aluminum AM03 Series Gunmetal Gray Machined Trailer Wheel part #AM73NR that you referenced.

view full answer...

Answer 8

Hey David! Without an exact match I would consider replacing the hub so you don't have an issue. Even if the hubs aren't original, they're probably older and this would give you a fresh start with your new to you boat trailer. Since it is…

view full answer...

Answer 9

Thanks for the pictures! The Aluminum Viking Series Valhalla Trailer Wheel item #AX02455545BMFL would be a great upgrade from the factory wheels that came with your Ranger's boat trailer. Your Goodyear ST215/75R14 tires will fit the 14" x…

view full answer...

Answer 10

Yes we have a 14 inch version of the Aluminum Viking Series Valhalla trailer wheel with the part #AX02455545BMFL. This is 5-1/2 inches wide and has the standard 5 on 4-1/2 inch bolt pattern that 14 inch trailer wheels have. I attached a picture of…

view full answer...

Answer 11

The differences from trailer wheels, like the Dexstar Conventional Steel Wheel with Offset #AM20504 that you referenced, and vehicle wheels, like GM OEM wheels, can vary based on a lot of things. Trailer wheels are specifically designed to be used…

view full answer...

Replacement Center Cap for Taskmaster Aluminum Viking Series Vor Trailer Wheel 3.19" Pilot Hole

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching