Solution for Replacement Spring Bars for Reese Pro Round Bar Weight Distribution

Question

Question:

Do replacements exist? Alternatively, are replacement spring bars from other manufacturers compatible such as Fastway 94-00-0800 or Eaz-Lift 48092. I would hate to have to purchase an entire kit when all I need is a replacement spring bar. I look forward to your reply

asked by: Michael S

0

Expert Reply:

Although there are some replacement parts available for your Reese Pro Round Bar Weight Distribution w Sway Control # RE94FR, Reese does not have replacement spring bars available. Spring bars from other manufacturers will not be compatible or fit the head on your Reese system. Currently, your only available solution would be to replace your springs bars by getting a new # RE94FR.

If you would like an option that does have replacement spring bars available, I recommend the Fastway e2 Weight Distribution w/ 2-Point Sway Control - Round - 8,000 lbs GTW, 800 lbs TW # FA94-00-0800. This has the same capacity as your Reese so it would be a great replacement option. You could use your existing hitch ball and will need the 1-7/8" 12pt Thin Walled Socket # ALL643216 for hitch ball installation.

expert reply by: Robin H

0

Answer 1

Hey Mike, so a friction sway control unit like the part #83660 can help stop some of the sway that starts from wind or passing semis but if you are experiencing persistent sway once you hit a certain speed that will only be fixed by increasing the…

view full answer...

Answer 2

The main reason for the price difference is the different construction used for the weight distribution hitches. The Reese Weight Distribution System #RP66540 uses mostly cast parts that are more expensive to manufacture. While the Reese Pro Round…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 6

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 7

Hey Bob. There's two possible locations for the brake controller port on your 2026 Ford F-150. The most likely one is on your dash behind the coin holder above the 4WD knob. It'll be connected to the back of the coin tray which is only…

view full answer...

Answer 8

Hey Michelle! There are definitely a lot of different weight distribution hitch (WDH) options out there. The most important thing is to make sure it is properly rated for the tongue weight of your setup. Looking at the specs for the 2022 Keystone…

view full answer...

Answer 9

Not another one! Just kidding Dirk! I was in the Marines I enjoy these conversion questions on the M1101 trailers. I'd be more than happy to list the parts you need, along with quantity, and confirm compatibility. 1 - Timbren Axle-Less Trailer…

view full answer...

Answer 10

Hi Joel! The easiest way to install a brake controller on your 2026 Toyota 4Runner would be to use the Redarc Tow-Pro Elite Brake Controller w/Custom Harness part #RED56CR. It is the same Redarc Tow-Pro brake controller as the RED44FR but has the…

view full answer...

Answer 11

This is a great choice Joe and thanks for reaching out! Weigh Safe True Tow Weight Distribution Hitch #WS49MR would be a good match for your setup. Since your Grand Design toy hauler will have a loaded tongue weight between 1,300 and 1,600 lbs, this…

view full answer...

Answer 12

Hey Roger, thanks for reaching out, and congrats on the new camper! For your Silverado and No-Bo 18.2 BeastMode, I really like the Fastway e2 setup. Here is what I recommend: - Fastway e2 Weight Distribution Hitch w/ 2-Point Sway Control - 10,000 lbs…

view full answer...

Solution for Replacement Spring Bars for Reese Pro Round Bar Weight Distribution

Products Featured in This Question

Featured Help Information

Miscellaneous Media

Continue Researching