Trailer Hitch Receiver That Fits 2010 Jeep Liberty

Question

Question:

Hitch fit 2010 Jeep Liberty? Thank You

asked by: Rick

0

Expert Reply:

Since you're looking for a trailer hitch receiver for your 2010 Jeep Liberty I recommend the etrailer Trailer Hitch Receiver # e85AR.

This is a Class III hitch with a 2" receiver. It has a bolt-on installation and a lifetime warranty.

expert reply by: Robin H

0

Answer 1

I recommend the etrailer Trailer Hitch Receiver #e85AR for your 2012 Jeep Liberty. This is our only receiver with the matte black powder coating that gives it a factory look since it matches the trim. It also has a 2" receiver for a wider…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 5

Hi David! There are quite a few hitches offered for your 2026 Honda Odyssey, so I definitely understand wanting to know the differences. There are basically three styles available for you and I have them broken out below: Exposed Crosstube: etrailer…

view full answer...

Answer 6

Hey Donny! For your Dometic Penguin/Brisk Air 15,000 BTU AC model B59516.711C0-MX, the correct soft start is the #DMC93JF. This is designed for Dometic Brisk II electronic air conditioner units with in-wall thermostats.

view full answer...

Answer 7

With your current Blue Ox tow bar the correct base plate kit is the part #BX1131 for your 2012 Jeep Liberty.

view full answer...

Answer 8

To install the #118384, you would need to unplug your existing 7-way harness from the rear of the socket. The #118384 would plug inline between the vehicle harness and the existing 7-way, as shown in the video I linked you to. If your Liberty does…

view full answer...

Answer 9

There are several factors that determine the towing capacity or weight carrying capacity of vehicles. Many times they may appear very similar but due to the frame, transmission or engine, the towing capacity can vary by quite a lot. My research…

view full answer...

Answer 10

The best solution I can provide for you would be a trailer bumper hitch like the part #C19101. This hitch is designed to attach to 2 by 4 inch bumpers, but with a 2 inch spacer you could attach it to your 2 by 2 inch bumper. You would need to provide…

view full answer...

Answer 11

I am not sure which spare tire carrier you saw in the video, however, the closest thing would be Roadmaster Spare Tire Carrier #RM-195125. This fits a 2" receiver and provides a spare tire mount on top, along with a 2" receiver opening…

view full answer...

Answer 12

Yes, a converter is needed for a 2011 Jeep Liberty because one the tail light circuits are on separate wires and they need to be combined for a trailer and two the factory tail light circuits are not sufficient to power the lights on a trailer as…

view full answer...

Trailer Hitch Receiver That Fits 2010 Jeep Liberty

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching