How to Remove Factory Bump Stops in 2020 Chevy Silverado 1500

Question

Question:

What tools do I need to remove rear bump stop?

asked by: Tom

0

Expert Reply:

To remove the existing bumpstop, you'll need a 10mm socket and a 6 inch extension.

I've linked to an install video that you might find helpful.

expert reply by: Mike L

0

Answer 1

Hey James, congrats on the new truck. The Timbren's need quite a bit of tongue weight on them to be helpful when towing, so what you're running into isn't too surprising. The only SumoSprings I have for a 2025 Silverado 1500 are item…

view full answer...

Answer 2

We have the Karrier part #AM32459 which would work great as a spare for your boat trailer as it's the right size tire and wheel bolt pattern.

view full answer...

Answer 3

Hey Kris. The Timbren Suspension Enhancement System item #T28MR is not compatible with the Trail Boss models of the 2021 Chevrolet Silverado 1500 so you'll need to go another direction. None of the suspension systems that replace or mount where…

view full answer...

Answer 4

There isn't an actual height difference between the SumoSprings Solo part #SS45FR and the #SS65FR that fits your 2021 Chevy Silverado 1500. The difference is related to the capacity. The 45 has the higher 1,500 lb capacity and the 65 has a 1,000…

view full answer...

Answer 5

For your 2020 Chevy Silverado 1500 I highly recommend the Firestone Ride-Rite Air Helper Springs #F2609. These air springs will offer excellent load support (up to 5,000 pounds) and their adjustability (5 psi to 100 psi) will let you fill the bags up…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

How to Remove Factory Bump Stops in 2020 Chevy Silverado 1500

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching