Can Curt RockerBall 2-5/16" Shock Absorbing Hitch Ball and Ball Mount Mount in Rise Position

Question

Question:

Can the ball be mounted with a ¾” rise instead of a 2” ?

asked by: Gian C

0

Expert Reply:

Yes, you can install the ball of the Curt RockerBall 2-5/16" Shock Absorbing Hitch Ball and Ball Mount w/ Sway Control Tab # C45WR in the rise position if you wanted which would give you the rise of 3/4 inch that you mentioned.

expert reply by: Jameson C

0

Answer 1

While there is no way to attach an anti sway system to the Glyder for Gen-Y part #325-GH-12005. I do have a solution for you. You can use the Convert-A-Ball Dual-Cushioned, Adjustable Ball Mount part #CAB-UM which isn't as clean looking of a…

view full answer...

Answer 2

Hi David, The Curt Ball Mount for 2" Hitches #C45030 is approximately 2-1/2" wide. The Reese Sway-Control Bracket #RP26003 can fit ball mounts that are smaller than 2-5/8" wide so these two components would be compatible with each…

view full answer...

Answer 3

Hey Brent! I would mount the Ark Drop Down Corner RV Stabilizer Jacks #ARK94FR on the outside as close to the corners as possible. If you mount them in the center of the trailer they won't add nearly as much stability. If you're worried about…

view full answer...

Answer 4

Hey Justin! I’d look at the etrailer Sidewind Trailer Jack - Swivel Bolt - 2K #e35YV for that. It mounts to the trailer frame instead of staying in the center A-frame jack location, and it fits trailer frames 2" to 4" tall; it should fit…

view full answer...

Answer 5

To add sway control to your 2018 Audi Q7 towing setup I highly recommend the Tuson Asymmetric Sway Control #335TSC-1000. I really like this unit because it activates the brakes on your trailer (per side as needed) when it senses the trailer start to…

view full answer...

Answer 6

Harvey, you’re right on target asking about sizing. The AFMD35121 was a 35k BTU unit that’s been discontinued. You can step into the 35K BTU #DMC74MR furnace by Dometic, but it is 2 inches taller than your current one. Most folks just enlarge the…

view full answer...

Answer 7

The ball of the Curt RockerBall 2-5/16" Shock Absorbing Hitch Ball and Ball Mount w/ Sway Control Tab #C45WR is not installed or torqued down when it arrives. You'll need to torque the nut to 250 ft lbs.

view full answer...

Answer 8

Yes, it will Clinton. The Curt Friction Sway Control for Weight Distribution Systems item #17200 uses a telescoping inner bar with friction pads to fight trailer sway. You can adjust the tension with the easily accessible handle. You will need a ball…

view full answer...

Answer 9

The two orange fittings at the ends of the RhinoFLEX RV Sewer Hose, part #CAM39761, are designed to come of easily. The ends can be removed by twisting the black locking rings until loose. From there, you can unscrew the orange fittings. This makes…

view full answer...

Answer 10

The anti-swivel base on the #C45WR is missing a tab on one side to make it compatible with the sway control tab. This does not adversely impact the performance. You can use the #C40047 with the #D320 but you would have to bend or cut one of the tabs…

view full answer...

Can Curt RockerBall 2-5/16" Shock Absorbing Hitch Ball and Ball Mount Mount in Rise Position

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching