Over Under Kit and MORryde Cushioned Equalizer and Wet Bolt Kit for Grey Wolf 23MKBL

Question

Question:

Which MORryde x factor cross support would I need? Thank you.

asked by: Bryce V

0

Expert Reply:

Since you have 3,500 lb axles that are 2-3/8 inch in diameter the correct over under kit would be the part # K71-384-00. For a cushioned equalizer kit the part # MR87ZR would be what you'd want and then for the upgraded hardware kit you'd want the part # MR46ZR.

expert reply by: Jameson C

0

Bryce V.

4/14/2022

Which MORryde x factor cross support would I need? Thank you.

Reply

Jameson C.

4/14/2022

MORryde has a version of the X-Factor Crossmember that was designed to work with the CRE3000 you have with the part # MR33WR.

Reply

Answer 1

It is likely you can avoid the drain line when installing the MORryde X-Factor Crossmember for Standard Frame Hangers #MR33WR by using the MORryde X-Factor Crossmember Adapter Kit for Drop Down Applications #MR43WR. I don't know exactly the…

view full answer...

Answer 2

Hey Henry, with leaf springs like the part #EM28AJ there isn't a torque spec for the shackle bolts that secure them as they need to be able to move freely. So the trick is to use lock nuts so they won't back off. So using them snug them up by…

view full answer...

Answer 3

Hey Richard! How did you measure your current leaf springs to get the 25-1/2" eye to eye measurement? We recommend jacking one side of the trailer up to get the weight off of them before measuring because they stretch out quite a bit over years…

view full answer...

Answer 4

Hey Mark, I looked up the specs of the spring you have now and found that it is a 24-3/4 inch long spring from eye center to eye center and for a 7k axle. So that means that the replacement spring part #EM28AJ that you referenced will work great as a…

view full answer...

Answer 5

If you are going to install two of the MORryde X-Factor Crossmembers #MR33WR on your tandem axle trailer Alan you would want to install them on the front and rear hangers. You can install a third one if you want on the middle hanger as well for even…

view full answer...

Answer 6

Hey Darla, the correct MORryde X-factor for trailers that have a MORryde CRE3000 kit installed is the standard kit part #MR33WR. Running three of these would give you the most stable setup so that would be what I would recommend.

view full answer...

Answer 7

Hello Rene, thanks for reaching out. It is pretty typical for RV manufacturers to use axles that are not rated for the full GVWR. They say this is because 10%-15% of the camper weight is on the hitch instead of the axles. They will put the bare…

view full answer...

Answer 8

Hello Chris, For your 2022 Grand Design Reflection 31MB 5th wheel with the MORryde CRE 3000 and wet bolt kit, the right crossmember brace is the MORryde X-Factor Crossmember #MR33WR. It helps stabilize your suspension, reduces stress by up to 94%,…

view full answer...

Answer 9

Hey Richard, thanks for reaching out! Yes, the MORryde X-Factor Crossmember for Standard Frame Hangers #MR33WR can be installed with the Roadmaster Comfort Ride #RM-2460-2570. Just as long as the X-Factor is installed on either of the end hangers as…

view full answer...

Answer 10

Hey Luis, We can answer both your questions in one as yes, you can change from the CRE3000 to AllTrek 4000, and it's definitely an upgrade worth making, as the AllTrek 4000 is better in a couple ways from the CRE3000. The first is the 4000 is…

view full answer...

Answer 11

Hey Jeff! I'm not sure who told you that but the information is incorrect. The MORryde X-Factor Crossmember can be used with the AllTrek 4000 like #MR29DR. The correct X-Factor crossmember is the #MR33WR which is the same as the XF12-001. You can…

view full answer...

Over Under Kit and MORryde Cushioned Equalizer and Wet Bolt Kit for Grey Wolf 23MKBL

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching