Replacement Master Cylinder for Aero 6000 Actuator

Question

Question:

I have a Master Tow dolly with the discontinued Aero 6000 hitch. Does #T2480000 directly replace the old hitch? How would I determine where to bolt it to the tongue?

asked by: Richard

0

Expert Reply:

For a replacement master cylinder for your Titan Aero 6000 drum brake actuator you can use Master Cylinder part # T4395100. This comes with everything you will need to complete the install.
(Please note that this item's description says it is for the Aero 7500, but it will also work for your Aero 6000).

If you access the master cylinder from below the coupler it will be pretty obvious how it all installs.

expert reply by: Jameson C

0

Answer 1

For your Titan Aero 6000 the correct replacement master cylinder is the part #T4395100 that you referenced and it comes with the piston inside of it as well.

view full answer...

Answer 2

If you can verify that the clunk noise is coming from the actuator, then a faulty damper would be the likely culprit. The damper controls the movement of the coupler into the actuator. The correct damper for your Titan Aero 6000 actuator is part…

view full answer...

Answer 3

Hi David; the old Dico Aero 6000 master cylinder can be replaced with the #T4395100. To add an electric lockout you can use the Replacement Solenoid Valve for Dexter Brake Actuators with Reverse Lockouts #T4748800.

view full answer...

Answer 4

For a Four Winns Boat Trailer with Titan Aero 6000 Surge Brake Actuator, I recommend replacement using the Titan Zinc-Plated, Leverlock Brake Actuator part #099-175-20 which is ready to go as is and will be a great fit. The reason I recommend…

view full answer...

Answer 5

The Titan Aero 6000 does use a slightly different bolt pattern as the Dexter Coupler part #099-175-20 so while it can work as a replacement you'd have to drill new holes or have the new coupler welded on. The brake line fittings are the same…

view full answer...

Answer 6

It does not come with instructions but it is pretty easy to replace. For your Titan Aero 6000 the correct replacement master cylinder is item #T4395100. This is the replacement master cylinder that works with drum brakes. I was able to find an…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 11

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Replacement Master Cylinder for Aero 6000 Actuator

Product Page this Question was Asked From

Continue Researching