Timbren Suspension Enhancement Fit For 2005 Chevy Silverado 2500 HD

Question

Question:

I have a 2005 Chevy Silverado 2500HD 2wd utility body, I can’t select the 2500 HD model, will these fit my truck? TGMRCK15S

asked by: Mike

0

Expert Reply:

While we do have an option for Timbrens that fit a 2005 Chevy Silverado 2500 HD, the part you mentioned is not a fit for that model truck. The correct fit for your Chevy is the following:

- Timbren Rear Suspension Enhancement System # TGMRCK25S

The # TGMRCK25S will fit both the 2WD and 4WD models of 2500 HD to help level the truck while minimizing body roll and sway.

expert reply by: Kyle S

0

Answer 1

For your 2005 GMC Sierra 2500 HD, there are two Timbren rear suspension compatible with it. The #TGMRCK25S have a weight capacity of 6000 pounds while the #TGMRTT35S have a weight capacity of 8000 pounds. More than likely you will only need the one…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 4

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 5

There are actually a couple differences between the Curt EZr #C619-648 and the Double Lock #C60712. The visible one will be that the safety chains on the #C60712 are not centered like the ones on the #C619-648. The difference that is not visible is…

view full answer...

Answer 6

Hey Michael, We have some hitch options available but I'll need a bit more information on your Silverado in order to find the correct fit. The available hitches are sectioned out by model (1500, 2500, 3500), bed length, and bumper type. If you…

view full answer...

Answer 7

Hey Eric, Using only 4 of the 5 mounting holes on #DE28YR is not recommended when installing new brakes. There is a chance of failure that could cause a lot more problems, it is best to install them exactly how they should be. With that said by far…

view full answer...

Answer 8

Hey Justin, thanks for reaching out! The Curt Trailer Hitch Receiver #C15312 will fit the long bed on your 2006 Chevy Silverado 2500HD so you're good to go!

view full answer...

Answer 9

We do have motors that you can add to your landing gear. For example, the Landing Gear Set #RVLG-8000 can be operated with the manual crank #RVLG-HDL but you can also add the motor #LC142178 and switch #LG-145236 for effortless operation on your end.…

view full answer...

Answer 10

In regards to the B&W Heavy-Duty Trailer Hitch Receiver part #BWHDRH25189, the distance from the flange to the top of the receiver tube is 3-1/8" and the distance from the rearmost mounting hole to the end of the receiver tube is…

view full answer...

Answer 11

You will want to find lights that match the lights you currently have on your trailer. If you have incandescent lights I recommend either staying with incandescent or swapping out all of the lights to LEDs. LED lights draw much less power, so you may…

view full answer...

Timbren Suspension Enhancement Fit For 2005 Chevy Silverado 2500 HD

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching