Replacement Bearings and Grease Seals for Dexter D60 6K Axle

Question

Question:

I need seals and bearings for Dexter 6000lb EZ lube axle. Numbers on the tag are D60, Dex# 1550135 date: 7/20/2009

asked by: Tommy G

0

Expert Reply:

Your 6K Dexter axle uses spindles that are compatible with a 25580 inner/ 14125A outer bearing and a 10-36 grease seal. We offer a replacement bearing kit as part # BK3-200 that includes the inner and outer bearings and races, the grease seal and a replacement cotter pin.

expert reply by: Mike L

0

Answer 1

You can use the Timken Grease and Oil Seal #TMK98ZR in place of the Grease Seal #GS-2250DL. While they are not exactly the same seal construction it is still a double lip design and the dimensions are the same so they are going to fit correctly.

view full answer...

Answer 2

Hey there Mark! That's a great idea to stock up on some spare parts. Most people don't have the foresight like that. You will need either Bearing Kit, 15123/25580 Bearings, GS-2125DL Seal #BK3-110 or Bearing Kit, 15123/ 25580 Bearings, 10-36…

view full answer...

Answer 3

I didn't receive a picture which you can email to me directly if you would like. However, since you have a Dexter D60 axle you will need the Bearing Kit, 14125A/ 25580 Bearings, 10-36 Seal item #BK3-200 you were looking at.

view full answer...

Answer 4

On Dexter axles manufactured after April 2001 you will be able to find the serial number stamped on the rear portion of the axle tube approximately 18" from the passenger side hub. Depending on the condition of the axle you may need some chalk…

view full answer...

Answer 5

If you are looking for the bearing kit we have our etrailer Kit #BK3-100 or the Timken Kit #TMK42VR which is going to match the Dexter bearing 031-029-02, 031-030-02 and seal 010-036-00 numbers you were given. It would be best to just order the 4…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 11

Hey Jeff. There is definitely a correlation between weight and capacity. I've listed the weight of all three of the Power Mountain Tallboy Off-Road Bottle Jacks we have below: Power Mountain Tallboy Off-Road Bottle Jack - 7-15/16" to…

view full answer...

Answer 12

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Replacement Bearings and Grease Seals for Dexter D60 6K Axle

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching