Is Demco Replacement Master Cylinder Compatible With Kodiak Disc Brake Kit

Question

Question:

Hi, Will the DM5919 work with Kodiak Disc Brake Kit K2HR526D? Thanks!

asked by: Michael N

0

Expert Reply:

Yes, the Replacement Master Cylinder w/ Inline Solenoid for Demco Actuators - Disc Brakes # DM5919 is compatible with the Kodiak Disc Brake Kit - 12" Hub/Rotor - 6 on 5-1/2 - Dacromet - 5,200 lbs to 6,000 lbs # K2HR526D.

expert reply by: Kyle S

0

Answer 1

The correct replacement for a Demco Master Cylinder 05680-C is the Replacement Master Cylinder part #5650. I spoke with Demco to confirm this for you.

view full answer...

Answer 2

Hey Mike, so the correct replacement for a Demco Master Cylinder 05680-C is the Replacement Master Cylinder part #5650. I spoke with Demco to confirm this for you and the bolt pattern is the same.

view full answer...

Answer 3

I spoke to my contact at Demco and he told that the Demco Hydraulic Brake Actuator #DM62VR should not slam forward when you slow down. He said this brake actuator is inertia based, meaning as you start to apply the brakes it will begin to slowly…

view full answer...

Answer 4

I am not aware of a bolt-on version of the Buyers Products Weld-On Safety Chain Retainer part #3375471000. However, if all you were wanting to do is mount your safety chains to the tongue of your trailer then you will just simply do so by running a…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 7

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 8

Hello Eric, The #K2R35DKG is Dacromet-coated, and the calipers are treated with KodaGuard. The #K2R35DS, on the other hand, is made entirely of stainless steel, hence the higher price. If you're in an area where road salt is common or if…

view full answer...

Answer 9

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 10

I currently have four different self-adjusting assemblies for your boat trailer with 10" x 2-1/4" electric drum brakes. You can choose from the following: -Terran Axle Electric Trailer Brakes #TX97ZJ (3,500 Axles) -etrailer Electric Trailer…

view full answer...

Answer 11

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 12

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Is Demco Replacement Master Cylinder Compatible With Kodiak Disc Brake Kit

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching