Tips for Running the Power Wire of a Powered Tail Light Wiring Harness Like # C56173

Question

Question:

Do you have a wiring diagram or instructions showing how to run the 12 volt wire from the battery to the trunk?

asked by: Don S

0

Expert Reply:

I attached a link to our FAQ page on running the power wire from a converter wiring harness like the Curt Wiring Harness # C56173 that you referenced to the vehicle battery.

expert reply by: Jameson C

0

Answer 1

The towing capacity for your 2014 Honda Accord EX-L is 1,000 lbs. Therefore, so long as the loaded weight of the trailer does not exceed this then you will be good to go. If the loaded weight of the trailer does exceed the above then we cannot…

view full answer...

Answer 2

Not all vehicles can handle the additional amperage draw of the trailer taillights on the vehicle taillight circuits. Even if those circuits are LED which do not draw that much relative to incandescent. Those vehicles need setup that draws power from…

view full answer...

Answer 3

There a few different ways to determine this. You can have a helper activate the turn signals, running lights and brakes. If a single bulb lights for each function (on each side of the car) then you have incandescent lamps. If you have LED's each…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…

view full answer...

Answer 12

Hey Ricardo! Yes, the Curt Trailer Hitch Receiver #C82RJ is the hitch Curt is working on for the new 2027 Telluride. This is a pre-order since Curt hasn't finished the design. It does not include wiring. The wiring harness for the 2027 is also up…

view full answer...

Tips for Running the Power Wire of a Powered Tail Light Wiring Harness Like # C56173

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching