Replacement Lens for Petersen Clearance Side Marker Trailer Light With Reflex Dimensions

Question

Question:

What are the masurments on this lense

asked by: Russell W

0

Expert Reply:

I went out to our warehouse and measured the Replacement Lens for Petersen Clearance Side Marker Trailer Light with Reflex # PE95ZR, and measured 3-3/16" long, 1-5/8" wide, and 2-3/4" on center between the mounting holes.

expert reply by: Bryce D

0

Replacement Lens Dimensions
(click to enlarge)

Answer 1

We do not carry an exact replacement unit for the MaxxAir Deluxe 8951K. We have the Smoke #MA00-07500K or White #MA00-07000K which would be the closest replacement. These fans use the same lift and fan motors but the control panels and circuit boards…

view full answer...

Answer 2

Hey Mike, it is important that you use the included power cable with the Furrion Vision S+ Wireless RV Backup System w/ 1 Camera #FR57AD like the instructions indicate. If this is like a hardwire install I would look for a cigarette lighter to 2-wire…

view full answer...

Answer 3

Hey John, congrats on the new truck! We can absolutely provide all the parts you need to flat tow your 2026 GMC Canyon AT4. We have the rebuild kit for the Falcon 2 tow bar as well. Here is what I recommend: - Roadmaster Direct-Connect Base Plate Kit…

view full answer...

Answer 4

Hey Kyle, for your Lippert Solera 2000 series awning you can use the Replacement Front Cover for Lippert Edge Awnings #LC32NJ for the front and #LC43UD for the rear and you'd be set! Did you damage yours?

view full answer...

Answer 5

Thank you for providing the part number from your trailer's marker light. Unfortunately I could find out only that this was evidently an Optronics product and I believe it is a rectangular light. Their website offers no results for that item so…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Replacement Lens for Petersen Clearance Side Marker Trailer Light With Reflex Dimensions

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching