Quick Pin No Latch Coupler That Accepts a 2" Hitch Ball and Bolts To a 3" Wide Trailer Tongue

Question

Question:

do you have a 2inch quick pin no latch coupler to fit 3inch channel

asked by: Craig L

0

Expert Reply:

Yes, we have the Curt QuickPin No-Latch Trailer Coupler # C54UR that fits a 3" channel and 2" ball. The coupler is rated for a trailer up to 3,500lbs.

expert reply by: Bud M

0

Answer 1

The Curt QuickPin No-Latch Trailer Coupler for 2" Ball part #C82CR is designed for a standard 2" wide x 3" tall trailer tongue. That said, it will work with any tongue size so long as it's 2" wide. It will not work with a…

view full answer...

Answer 2

For your Curt Coupler 25138 which is similar to their Curt QuickPin No-Latch Trailer Coupler #C54UR, they recommend using grade 5, 1/2" bolts and nuts. If you have an open channel on your straight tongue trailer you will need to use 4 bolts and…

view full answer...

Answer 3

Thank you for your purchase from etrailer of the Curt QuickPin No-Latch Trailer Coupler for 2" Ball - 3" Channel - 3,500 lbs #C54UR. The 100 ft lbs is too much, as the directions specify to torque the bolts to 55 ft lbs. When you over…

view full answer...

Answer 4

There are a couple of different ways you can lock the Curt QuickPin No-Latch Trailer Coupler for 2" Ball, either with a standard coupler lock, or you can use a 1/2 inch diameter hitch pin lock, since that is the same size as the pin and clip…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 11

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 12

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Quick Pin No Latch Coupler That Accepts a 2" Hitch Ball and Bolts To a 3" Wide Trailer Tongue

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching