Can the Demco 32-Degree A-Frame Trailer Coupler Be Bolted On

Question

Question:

Hello, Can I drill holes and use this as a bolt on ? thanks

asked by: Darren A

0

Expert Reply:

The Demco 32-Degree A-Frame Trailer Coupler part # DM15633-81 must be welded per the manufacturer. I'm sure you could drill holes and attach the coupler that way but we can't recommend this. The weight capacity would be severely compromised if not welded. The location of the holes and size are all crucial factors that require extensive testing for bolt-on applications which we cannot provide for the above.

expert reply by: Conner L

0

Answer 1

You could drill into the Bulldog #BD028463 and make it a bolt-on but that's not really ideal. We don't have the exact match in a bolt-on model. We do have part #BD44150WH301 for a bolt-on Bulldog coupler. It has a higher rating but the price…

view full answer...

Answer 2

The etrailer A-Frame Trailer Coupler w/ Round Jack Hole #CA-5280-RB uses the standard a-frame angle of 50 degrees. The length from the rear of the coupler to where the coupler meets its narrowest point is approximately 9" long. I have include…

view full answer...

Answer 3

Hey Wayne! The Demco 32-Degree A-Frame Trailer Coupler #DM15633-97 is only designed to be welded on. Demco doesn't have a bolt-on equivalent so if you want the eZ Latch for a 32º frame this is the only option available. If you need anything…

view full answer...

Answer 4

As far as I know your 2008 Victory trailer has an A-frame on it. Assuming that is correct, and it is a 50 degree A-frame, I recommend one of the following: -Demco 50-Degree A-Frame Trailer Coupler #DM16680-52 (Bolt-On, Silver Powder Coat) -Demco…

view full answer...

Answer 5

We currently have three versions of the Demco 32 degree A-Frame coupler but none of them are zinc plated. We have the part #DM15633-97 which is primered, the part #DM15633-81 which is powder coated black, and we have the part #DM15633-52 which is…

view full answer...

Answer 6

The Demco 6-Hole Adjustable Channel Bracket - Weld On - 12" Tall - 21,000 lbs #DM66134 is the weld on option for your trailer. There isn't a complete kit we offer, but it sounds like you are seeking the Demco 50-Degree A-Frame Coupler…

view full answer...

Answer 7

First I want to make sure you verify your channel mount for the Demco Trailer Coupler #DM14040-81 has a 21K or larger capacity as often times they are less like the Demco #DM15349-52 which often times people look at and think it is a channel mount…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Can the Demco 32-Degree A-Frame Trailer Coupler Be Bolted On

Product Page this Question was Asked From

Continue Researching