8-1/2 Foot Awning For A Scamp Trailer

Question

Question:

What kit would you recommend for a Scamp trailer. I have a hideaway 85 to replace the factory awning.

asked by: Ed K

1

Helpful Expert Reply:

The Thule HideAway Awning # TH490018 would work great for your Scamp trailer, and will bolt directly to your trailer's sidewall with the included hardware.

This awning is 8-1/2' long and 6-1/2' wide, and operates via hand crank to open and close your awning in seconds.

expert reply by: Bryce D

1

Answer 1

The Timbren Axle-Less Trailer Suspension System part #ASR1THDS01 is a great option for a 2018 Scamp 13' Trailer with 2,200 lb axle. This system would allow you to reuse both your hubs/drums and braking assemblies if equipped.

view full answer...

Answer 2

We do have lift kits available for torsion axles but they are designed for specific Dexter Torflex Axles. For example, the Torflex Lift Kit part #K71-707-01 is designed for a Dexter #10 Torflex Axle which has a 2,300 to 4,000 lb weight capacity. If…

view full answer...

Answer 3

For the Timbren Heavy-Duty Axle-Less Trailer Suspension - 4" Lift Spindle - Regular Tires - 2,000 lbs #ASR2KHDS04, I've attached a photo with all the dimensions you were seeking but the basic plate dimensions are 4-3/4 inches by 13 inches…

view full answer...

Answer 4

The Timbren Axle-Less system would be a great option to replace your current axle on your Coleman pop-up trailer. The Timbren system that I like for your trailer is #ASR2KHDS04. This suspension has a 2000 lbs weight capacity and includes 4 inch lift…

view full answer...

Answer 5

We can definitely get your Little Guy Silver Shadow an upgrade to replace your torsion axle, and I recommend going with the Timbren Axle-Less Suspension System. They give you an improved ride compared to a traditional through-axle because they work…

view full answer...

Answer 6

Hey Brad, thanks or reaching out! Yes, ultimately, it's just the castle nut and cotter pin that comes with the Timbren Kit #ASR2KHDS04 that will be keeping the idler hub #AKIHUB-545-35-EZ-K on the spindle. It sounds a little wild when you think…

view full answer...

Answer 7

You can replace your Scamp 19 5th wheel trailer's torsion axle with a Timbren axle-less system that has a lift, and according to my research, a Scamp 19 5th wheel has a 3,500 lb torsion axle. While I do recommend verifying that, what you can use…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 12

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

8-1/2 Foot Awning For A Scamp Trailer

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching