Availability of 2-1/2 Inch Pipe-Mount Sidewind Jack with 15 Inch Lift and Drill Power Option

Question

Question:

Looking for a 15 lift Side mount, side wind on a 2.5 pipe mount. Want one you can use a drill with

asked by: Dave W

0

Expert Reply:

If you want a sidewind jack with a drill power option, you are looking at the Trailer Valet JXC/JXS # TV34FR or # TV64FR. The only problem here is these only have 14" of travel and they are not a pipe mount. These are currently the only sidewind options that will allow you to use a drill to operate them.

For a jack that has everything you need except the drill power option, I recommend the Bulldog Round, Pipe-Mount Swivel Jack # BD198250. This jack uses a side frame mount, sidewind, has a 2-1/2" pipe mount, 15" lift, and 7,000 lb lift capacity. The bracket height is 16" retracted and 31" extended.

I have attached some review videos for your reference.

expert reply by: Robin H

0

Answer 1

No worries Lorelei, I'm here to help! An electric jack is more of an upright only jack, whereas the manual options can have the ability to swivel to the stowed/concealed position for storage. Do you know if you have the mounting hole cutout…

view full answer...

Answer 2

Hey Gwen! The distance from the center of the mounting hole to the bottom of the Trailer Valet JX Trailer Jack #TV35FR when fully retracted is 13.44". If you’re measuring from the bottom of the pipe mount instead of the center of the hole, that…

view full answer...

Answer 3

Hello Evan, thanks for reaching out. Sadly, the Round, Pipe Mount Swivel Jack #TJP-5001S-B does not have any kind of provision for operating with a drill. For that jack it will be the hand crank only. If you are looking for a jack that can be…

view full answer...

Answer 4

The Trailer Valet #TV64FR JXS 5K trailer jack is a pipe mount swivel jack that can be removed from the trailer by pulling the pin shown in the provided photo. If you click the provided link, you can see a video showing a typical installation.

view full answer...

Answer 5

Hi Craig; thank you for providing those part numbers. That is the 2.25" inner diameter grease seal so for replacement bearings you can use the Bearing Kit, LM67048/25580 Bearings, 10-36 Seal #BK3-300 you were looking at. If you prefer Timken…

view full answer...

Answer 6

Thanks for the information and picture James! Your Curt 5,100 lbs capacity axle uses item #25580 inner bearings and item #LM67048 outer bearings. So you would need the Bearing Kit item #BK3-300, which includes both bearings, along with both races, a…

view full answer...

Answer 7

I was unable to find any information with the numbers on your axle, unfortunately. However, you can contact the manufacturer of the trailer and they should be able to tell you exactly which inner and outer bearings you have. If for some reason they…

view full answer...

Answer 8

You will need to remove your hub, remove the seal and get the bearing numbers and seal numbers from what you have right now and then you will be able to pick out the correct kit. I attached a picture that shows bearings, races, and seals where you…

view full answer...

Answer 9

Initially what you need to do is clean out all of the grease in your hub, on/in the bearings, and on the spindle. Once that is done you simply swap out the grease seal for the oil seal included in the Kodiak XL ProLube Kit #XLPROLUBE2440KIT (which…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Availability of 2-1/2 Inch Pipe-Mount Sidewind Jack with 15 Inch Lift and Drill Power Option

Products Featured in This Question

Featured Help Information

Miscellaneous Media

Continue Researching