Suspension Enhancement For A 2022 Kia Telluride

Question

Question:

DO you have any suspension enhancements for a 2022 Kia Telluride

asked by: Teresa

0

Expert Reply:

For your 2022 Kia Telluride, we do have an option for you. The Air Lift 1000 Air Helper Springs for Coil Springs # AL29PD will fit all models of the 2022 Kia Telluride and provides up to 1,000lbs of load leveling support, that will help reduce tire wear and OEM suspension strain.

This kit will help keep your vehicle level while hauling a heavy load as well.

expert reply by: Bryce D

0

Answer 1

For starters, a breakaway switch will need to have a separate and independent battery according to most state regulations so it may be beneficial to check with your local DMV or DOT before proceeding. The Hopkins Engager Push-To-Test Trailer…

view full answer...

Answer 2

Hey Freddy, that's definitely an interesting situation you've got with the Air Lift 1000 Air Helper Springs for Coil Springs #AL29PD so I did some poking around the internet, and it sounds like it could be a couple of things, but it should be…

view full answer...

Answer 3

We have a couple options for your sagging 2024 Kia Telluride. The first is the easiest to install and is maintenance free so you will not have do anything after you install them. They are the Coil SumoSprings Custom Helper Springs #CSS-1125R. These…

view full answer...

Answer 4

Hey Stephen, I would go with the SumoSprings kit part #CSS-1125R if you prefer a zero maintenance solution that once you install it you can basically never have to think about it again. The Air Lift air bag kit part #AL29PD would also work but it…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 10

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 11

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Suspension Enhancement For A 2022 Kia Telluride

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching