Ground Clearance on a 2020 Hyundai Sonata w/ the Draw-Tite DT74MR Hitch Receiver
Published 12/21/2021
Products Featured in This Question
Question:
How much ground clearance is there from the installed hitch? Does the receiver opening end past the rear bumper, and if not, how far out does the ball receiver have to extend to clear the rear bumper?
asked by: Chris
Expert Reply:
I just spoke with my rep at Draw-Tite the bottom of the 1 1/4" receiver for the Draw-Tite Sportframe Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4" item # DT74MR sits 5 1/2" off of the ground. I have attached a picture of the hitch installed on a Hyundai Sonata. The receiver extends to the trim but not past the bumper. I recommend using the Curt Class II Drawbar - 5" Rise - 9-5/8" Long item # C45014 to make sure you have enough clearance to get past your Sonata's bumper. If you need a hitch ball, we have a 2" ball item # C40018 and a 1 7/8" ball item # C40001.
(click to enlarge)
Product Page this Question was Asked From
Draw-Tite Sportframe Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4"
- Trailer Hitch
- For Towing
- Class I
- 200 lbs TW
- 2000 lbs GTW
- 1-1/4 Inch Hitch
- Visible Cross Tube
- Draw-Tite
more information >
Featured Help Information
Instructions
Continue Researching
- Shop: Curt Class II Drawbar - 5" Rise - 9-5/8" Long - 3,500 lbs
- Shop: Hub Bearing Kit for Lippert, Dexter, and AL-KO Axles - 3,500 lb with #84 Spindle
- Shop: Trailer Hitch
- Shop: Draw-Tite Sportframe Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4"
- Shop: Master Lock Hitch Receiver and Coupler Latch Lock Set - Padlock - 1-1/4" and 2" Hitches
- Article: How to Measure for Trailer Hitch Drop
- Search Results: 44649
- Q&A: Recommendation for 1-1/4 Inch Ball Mount with 8 Inch Rise
- Q&A: Is there a Euro Style Ball Mount with a 5 Inch Rise for a 2016.5 Mazda CX-5
- Search Results: spare tire mount
- Video: Review of the Curt Class II Drawbar
- Q&A: Replacement Trailer Hub Grease Seal for TCM 17255TB Seal
- Search Results: trailer hitch ball mount
- Search Results: fits 1~1/4 inch hitch trailer hitch ball mount
- Shop: Timken Bearing Kit for Lippert, Dexter, and AL-KO Axles - 3,500 lb with #84 Spindle
- Shop: Bearing Kit, 14125A/25580 Bearings, GS-2125DL Seal
- Shop: Timken Bearing Kit, 14125A / 25580 Bearings, 14276/25520 Races, 10-36 Seal
- Article: Best Bike Racks for Electric Bikes
- Q&A: Does Heat Shield of 2020 Hyundai Sonata Need to Remove to Install Draw Tite Trailer Hitch
- Q&A: Is there a 2 Inch Hitch for a 2021 Hyundai Sonata?
- Q&A: Draw-Tite Hitch Receiver and Kuat Bike Rack for 2022 Hyundai Sonata
- Q&A: Will Removing Heat Shield to Install Hitch on 2020 Hyundai Sonata Cause Damage to Vehicle
- Search Results: 1 1/4 inch hitch
- Search Results: trailer jack
- Shop: Brake Controller
- Video: Feature Review 2" Hitch Ball
- Video: Draw-Tite Drawbar for 1-1/4" Hitches Review
- Video: What to Know About the 2" Hitch Ball
- Video: 2" Hitch Ball Spec Review
- Video: Let’s Check Out the 2" Hitch Ball